Guillaume Bourque's Discussions (13)

Search Forum

View

Discussions Replied To (10) Replies Latest Activity

"Wow, thanks for the explanation it's like you were righ tthere ! But Why dit it whe…"

Guillaume Bourque replied Oct 6, 2012 to my lipo crash my 3DR hexa

 3 Oct 7, 2012
Reply by Stephen Roach

"I have no luck after redoing all the setup ..... I will retrun my APM2 board to my g…"

Guillaume Bourque replied Jun 7, 2012 to APM2 output #1 is fried, may I change the code to use channel 2-7 ?

 13 Jun 7, 2012
Reply by Guillaume Bourque

"Well i finally manage to install my own version of the soft on my APM2, I did it wi…"

Guillaume Bourque replied Jun 5, 2012 to APM2 output #1 is fried, may I change the code to use channel 2-7 ?

 13 Jun 7, 2012
Reply by Guillaume Bourque

"Hi all, after retrying I have no luck.   I can compile and update the code on the A…"

Guillaume Bourque replied Jun 5, 2012 to APM2 output #1 is fried, may I change the code to use channel 2-7 ?

 13 Jun 7, 2012
Reply by Guillaume Bourque

"I will reconnect everything with no pros and redo all the calibration and report bac…"

Guillaume Bourque replied Jun 5, 2012 to APM2 output #1 is fried, may I change the code to use channel 2-7 ?

 13 Jun 7, 2012
Reply by Guillaume Bourque

"Thanks, One more question, if I may ask. I have modify the file. I'm running ardu…"

Guillaume Bourque replied Jun 5, 2012 to APM2 output #1 is fried, may I change the code to use channel 2-7 ?

 13 Jun 7, 2012
Reply by Guillaume Bourque

"Wow great, thanks, I will try this later today. I will probably get a new APM2 boar…"

Guillaume Bourque replied Jun 5, 2012 to APM2 output #1 is fried, may I change the code to use channel 2-7 ?

 13 Jun 7, 2012
Reply by Guillaume Bourque

Developer

"Hi, any luck I could change the code to use output channel 2-7 on my APM2 for my 3D…"

Guillaume Bourque replied Jun 5, 2012 to ArduCopter 2.5 released!

 1708 Dec 21, 2012
Reply by Emin Bu

"Since I'm not the only one with a flip on take off (http://www.diydrones.com/forum/t…"

Guillaume Bourque replied Jun 5, 2012 to APM2 output #1 is fried, may I change the code to use channel 2-7 ?

 13 Jun 7, 2012
Reply by Guillaume Bourque

"It was a bad ESC for motor #1 it went crazy and the copter flip and I did not cut th…"

Guillaume Bourque replied Jun 4, 2012 to APM2 output #1 is fried, may I change the code to use channel 2-7 ?

 13 Jun 7, 2012
Reply by Guillaume Bourque

RSS

Social Networking

Top Content 

1 APM Project vs DJI NAZA and WOOKONG

APM Project vs DJI NAZA and WOOKONG
2 APM 2.5 with NEO-6M ublox gps (not 3DR LEA-6)

APM 2.5 with NEO-6M ublox gps (not 3DR LEA-6)
3 APM Copter 2.9.1.b has been released

APM Copter 2.9.1.b has been released
4 Flying 3D Spline Curves between Waypoints with ArduCopter 3.0

Flying 3D Spline Curves between Waypoints with ArduCopter 3.0
5 ArduCopter-3.0 ready for wider use

ArduCopter-3.0 ready for wider use
6 10k autonomous flight - telemetry guided flight, and other APM tests!

10k autonomous flight - telemetry guided flight, and other APM tests!
7 Drone shot down by police

Drone shot down by police
8 MAAT final version is being tested

MAAT final version is being tested
9 Help Tuning Arduplane 2.73 With A Large Slow Airframe

Help Tuning Arduplane 2.73 With A Large Slow Airframe
10 Thirty Days (#28): McMaster-116 lift

Thirty Days (#28): McMaster-116 lift

Contests

Season Two of the Trust Time Trial (T3) Contest has now begun. The fourth round is an accuracy round for multicopters, which requires contestants to fly a cube. The deadline is April 14th.

A list of all T3 contests is here. 

Groups

Advertisement

© 2013   Created by Chris Anderson.   Powered by

Badges  |  Report an Issue  |  Terms of Service