Developer

Pete Hollands's Discussions (104)

Search Forum

View

Discussions Replied To (104) Replies Latest Activity

"Possibly best to have MAVLink use wind vectors (computer to computer ), and then it…"

Pete Hollands replied Nov 18, 2012 to Calculated wind vector.180deg out

 7 Nov 18, 2012
Reply by Tim McPherson

"Note: UDB uses wind vectors, not wind direction. It would be nice to have a MAVLink…"

Pete Hollands replied Nov 18, 2012 to Calculated wind vector.180deg out

 7 Nov 18, 2012
Reply by Tim McPherson

"Take a look at the landing here with 90 degree flaps on a funcub. (near beginning of…"

Pete Hollands replied Nov 1, 2012 to Landing on a forest clearing ( or on a short field in general)

 5 Nov 1, 2012
Reply by Martin

"Warren, In MAVLink 1.0 there is an extra CRC process step. For every XML message in…"

Pete Hollands replied Jul 4, 2012 to Has CRC16 Calculation Changed from MAVLink 0.9 to 1.0?

 11 Jul 22, 2012
Reply by Jake Stew

3D Robotics

"Jebadiah, Most of the specification for theUDB 4 is provided by Sparkfun as they man…"

Pete Hollands replied May 20, 2012 to Discussion forum for UAVDevBoard, Sparkfun's 3-axis IMU-based autopilot board

 705 May 20, 2012
Reply by Jebadiah Moulton

3D Robotics

"OK. So you are programming the board. Throttle is by default on channel 3 in options…"

Pete Hollands replied May 20, 2012 to Discussion forum for UAVDevBoard, Sparkfun's 3-axis IMU-based autopilot board

 705 May 20, 2012
Reply by Jebadiah Moulton

3D Robotics

"Hi Jebadiah,  After completing step 10 on page 13, do you get the message:- "Program…"

Pete Hollands replied May 20, 2012 to Discussion forum for UAVDevBoard, Sparkfun's 3-axis IMU-based autopilot board

 705 May 20, 2012
Reply by Jebadiah Moulton

3D Robotics

"Brainstorming Possibilities:- Use MatrixPilot from Trunk with MAVLink (subject to ve…"

Pete Hollands replied May 20, 2012 to Discussion forum for UAVDevBoard, Sparkfun's 3-axis IMU-based autopilot board

 705 May 20, 2012
Reply by Jebadiah Moulton

3D Robotics

"Mark, I flew that way for years without rudder control with my Twinstar 2. It works…"

Pete Hollands replied Apr 18, 2012 to Discussion forum for UAVDevBoard, Sparkfun's 3-axis IMU-based autopilot board

 705 May 20, 2012
Reply by Jebadiah Moulton

3D Robotics

"Hi Mark, Yes, to get to Stabilized mode and Autnomous mode you will need to get GPS…"

Pete Hollands replied Apr 17, 2012 to Discussion forum for UAVDevBoard, Sparkfun's 3-axis IMU-based autopilot board

 705 May 20, 2012
Reply by Jebadiah Moulton

RSS

Social Networking

Top Content 

1 APM 2.5 with NEO-6M ublox gps (not 3DR LEA-6)

APM 2.5 with NEO-6M ublox gps (not 3DR LEA-6)
2 APM Copter 2.9.1.b has been released

APM Copter 2.9.1.b has been released
3 APM Project vs DJI NAZA and WOOKONG

APM Project vs DJI NAZA and WOOKONG
4 Flying 3D Spline Curves between Waypoints with ArduCopter 3.0

Flying 3D Spline Curves between Waypoints with ArduCopter 3.0
5 Misadventures in power electronics

Misadventures in power electronics
6 Drone shot down by police

Drone shot down by police
7 MAAT final version is being tested

MAAT final version is being tested
8 10k autonomous flight - telemetry guided flight, and other APM tests!

10k autonomous flight - telemetry guided flight, and other APM tests!
9 ArduPlane 2.73 released

ArduPlane 2.73 released
10 Help Tuning Arduplane 2.73 With A Large Slow Airframe

Help Tuning Arduplane 2.73 With A Large Slow Airframe

Contests

Season Two of the Trust Time Trial (T3) Contest has now begun. The fourth round is an accuracy round for multicopters, which requires contestants to fly a cube. The deadline is April 14th.

A list of all T3 contests is here. 

Groups

Advertisement

© 2013   Created by Chris Anderson.   Powered by

Badges  |  Report an Issue  |  Terms of Service