ArduCopter2 Trouble connecting

I have connected and uploaded the new code via mission planner. I have gone through the setup with the CLI and MP. When I slide the switch forward to the fly position and try to connect to the mission plannner it never connects even with gps lock? I've even tried to connect via Xbee's set at 56700, but nothing. All the lights are good "A" is solid green. I do NOT have it conneccted to the Rx or ESC does that matter? I'm trying to make sure everything is working first. 

Tags: connecting, truoble

Views: 122

▶ Reply to This

Replies to This Discussion

Permalink Reply by Jeff Griffith on May 9, 2011 at 6:29am
I get this error every time I try to build the code. The definition of the function get_log_boundaries is in the wrong place. You need to move the function get_log_boundaries up in the file to before the first place it is called.  I'm not sure how anyone else is getting the 'out of box' code to compile.  I've never been able to compile AC2 without modifying this file.
Permalink Reply by Willems Helmut on May 9, 2011 at 6:39am
can you place the file here pls so that i can look
Permalink Reply by Jeff Griffith on May 9, 2011 at 6:43am
Not right now.  :(  I'm at work and don't have access to my Arducopter build environment.  I will when I get home (~ 8 hours from now).
Permalink Reply by MB1380 on May 9, 2011 at 12:59pm

Im getting the same mavlink bad packet error. 

It works fine for updating the software but not in the sensor section??

 

I had it all working fine last week on a pre release version. Only got this error today when i loaded the zip'd code.

Permalink Reply by Al Ros on May 9, 2011 at 9:31pm

I downloaded latest trunk version and that seems to have corrected the lack of connect issue.

Al

Permalink Reply by Russell B. Sutton on May 9, 2011 at 9:41pm

I've have never download from the truck.  how do i where i go?

 

Permalink Reply by Russell B. Sutton on May 9, 2011 at 11:08pm
I got them downloaded and re-loaded the APM,  Yes it connects know via Xbee but it doesn't talk.  HK_CGS doesn't work either.  I have tried adding #defines and i've tried several Xbee baund rates.  Somethings still not right with the .pde file.  I guess will have to wait for an update.
Permalink Reply by MB1380 on May 10, 2011 at 4:20am
Ya, i got it working with the latest version now aswell.
Permalink Reply by Russell B. Sutton on May 10, 2011 at 5:30am

U got ? what work?  Just APM or APM with Xbee?

 

RSS

Social Networking

Top Content 

1 ArduPlane 2.73 released

ArduPlane 2.73 released
2 How to analyze a crash?

How to analyze a crash?
3 ArduVTOL

ArduVTOL
4 NEVER connect a Capacitor backup or voltage protector on APM board

NEVER connect a Capacitor backup or voltage protector on APM board
5 HD video for UAV's

HD video for UAV's
6 APM Copter 2.9.1.b has been released

APM Copter 2.9.1.b has been released
7 DIYDrones Chat Feature Info

DIYDrones Chat Feature Info
8 Arducopter Question

Arducopter Question
9 Arducopter 3Dr or Phantom

Arducopter 3Dr or Phantom
10 ArduVTOL - Wingcopter - Flight Report Nr.1

ArduVTOL - Wingcopter - Flight Report Nr.1

Contests

Season Two of the Trust Time Trial (T3) Contest has now begun. The fourth round is an accuracy round for multicopters, which requires contestants to fly a cube. The deadline is April 14th.

A list of all T3 contests is here. 

Groups

Advertisement

© 2013   Created by Chris Anderson.   Powered by

Badges  |  Report an Issue  |  Terms of Service