CLI Problem

I went to use the CLI for APM prior to a flight yesterday and I cant get it it to respond to any commands. The CLI opening screen will display correctly, but when I enter a command i get no response. I have tried in both the mission planner, and serial monitor in Arduino, Yes I did have carrage return set and baud rate set correctly. I have tried reloading the code to APM but still have not rectified the problem, Not sure what could have changed to cause the problem.

 

Anybody got any ideas?

Cheers

Views: 16

▶ Reply to This

Replies to This Discussion


3D RoboticsPermalink Reply by Chris Anderson on November 19, 2010 at 8:28am
That was a bug in a previous release of the code., which has now been fixed. Please download it again and replace your current files. (The bug fix is in the libraries, so replace them, too)
Permalink Reply by Darren on November 19, 2010 at 3:56pm
Chris, I just downloaded the featured zip (from 40hrs ago) extracted, and replaced libraries from within the zip, but still has the same cli issue.

3D RoboticsPermalink Reply by Chris Anderson on November 19, 2010 at 4:02pm
Try a different browser. Yours may be caching the old file because it has the same filename.
Permalink Reply by Jon Keller on November 20, 2010 at 3:09am
I have the same issue with the newly downloaded APM. (My last one was over 2 weeks old and CLI was working fine.)
Permalink Reply by Paul Thompson on November 20, 2010 at 3:54am
I have tried the latest code, and have tried it again in another browser, but I am still getting the same issue.

3D RoboticsPermalink Reply by Chris Anderson on November 20, 2010 at 9:20am
Hmm. I may have uploaded an old version by mistake this week. Let me check it today...stay tuned.

3D RoboticsPermalink Reply by Chris Anderson on November 20, 2010 at 10:54am
Updated. Please download it again and try (again, make sure it hasn't cached an old file)
Permalink Reply by The Old Flyer on November 20, 2010 at 11:10am
Chris,
I am having the same problem as Paul even after deleting the ArduPilotMega folder then downloading the latest .zip file.

3D RoboticsPermalink Reply by Chris Anderson on November 20, 2010 at 12:40pm
I think this is because Google Code or browsers are cacheing the old file, because I used the same file name. I've now changed the file name. See if this one works.
Permalink Reply by Jon Keller on November 20, 2010 at 1:17pm
1.01 is working for me now.
Permalink Reply by The Old Flyer on November 20, 2010 at 2:31pm
The CLI is working for me now too.
Thanks for all the good work!
Permalink Reply by Paul Thompson on November 20, 2010 at 9:33pm
1.01 also working for me, thanks for the update, I can fly again now :)

RSS

Social Networking

Top Content 

1 ArduCopter-3.0 ready for wider use

ArduCopter-3.0 ready for wider use
2 APM Project vs DJI NAZA and WOOKONG

APM Project vs DJI NAZA and WOOKONG
3 Flying 3D Spline Curves between Waypoints with ArduCopter 3.0

Flying 3D Spline Curves between Waypoints with ArduCopter 3.0
4 APM 2.5 with NEO-6M ublox gps (not 3DR LEA-6)

APM 2.5 with NEO-6M ublox gps (not 3DR LEA-6)
5 APM Copter 2.9.1.b has been released

APM Copter 2.9.1.b has been released
6 10k autonomous flight - telemetry guided flight, and other APM tests!

10k autonomous flight - telemetry guided flight, and other APM tests!
7 MAAT final version is being tested

MAAT final version is being tested
8 Getting ready for Arducopter 3.0

Getting ready for Arducopter 3.0
9 Help Tuning Arduplane 2.73 With A Large Slow Airframe

Help Tuning Arduplane 2.73 With A Large Slow Airframe
10 How to succeed without really trying

How to succeed without really trying

Contests

Season Two of the Trust Time Trial (T3) Contest has now begun. The fourth round is an accuracy round for multicopters, which requires contestants to fly a cube. The deadline is April 14th.

A list of all T3 contests is here. 

Groups

Advertisement

© 2013   Created by Chris Anderson.   Powered by

Badges  |  Report an Issue  |  Terms of Service