HM-TRP 868, Sik software link problems

Hi all,

I've read the instructions, installed the software and can compile it (make) without any error messages.
But when I issue make install I get these:

LD obj/hm_trp/bootloader.hm_trp/bootloader.hm_trp.hex
SIZECHECK obj/hm_trp/bootloader.hm_trp/bootloader.hm_trp.hex: CSEG 609 HIGHCSEG 182
PATCH obj/hm_trp/bootloader.hm_trp/bootloader.hm_trp.433.hex
Traceback (most recent call last):
  File ".//tools/hexpatch.py", line 62, in <module>
    f = open(args.inputfile, mode="r")
IOError: [Errno 2] No such file or directory: './/obj/hm_trp/bootloader.hm_trp/bootloader.hm_trp.hex'
make[1]: [obj/hm_trp/bootloader.hm_trp/bootloader.hm_trp.433.hex] Error 1 (ignored)

I've traced it down to the linker step, because no .hex files are created.

Can someone help me out ?

I just need the:
obj/hm_trp/bootloader.hm_trp/bootloader.hm_trp.868.hex
obj/hm_trp/radio.hm_trp/radio.hm_trp.hex

files.

Thanks,
Amilcar Lucas

Views: 1406

▶ Reply to This

Replies to This Discussion

Permalink Reply by Jan on December 22, 2012 at 6:27am

Marcin,

I uploaded the bootloader.hm_trp.hex, via the slabprog.
This worked just fine and as you said the red led stays on.

Afterwards I hooked the module up to the 3DR radio config tool and uploaded the firmware. This also worked fine.
However when I try to 'Load the settings' it doesn't seem to work.
Nothing on the terminal, nor on the RSSI measurements.
Do you have any thoughts or suggestions that I could check?

Regards,

Permalink Reply by Marcin Krawczyk on December 22, 2012 at 6:54am

Wrong :-)

You have to use different bootloader for different freq (I don't know, what is bootloader.hm_trp.hex for), i.e. for 433MHz module you have to use bootloader.hm_trp.433.hex etc.

Permalink Reply by Jan on December 22, 2012 at 9:53am

Ok my fault :-)

Just uploaded the bootloader.hm_trp.433.hex and uploaded the firmware.

Working smoothly now. Loading the config is working as well.
Now taking care of the other module and give it a try with the APM and MP.

Thanks again for the support and fast response.

Best regards

Permalink Reply by AS on September 4, 2012 at 6:27am

Hi guys!

Is there anyway to upload a new firmware to the modules without the drones app?

Regards,

AS

RSS

Social Networking

Top Content 

1 ArduPlane 2.73 released

ArduPlane 2.73 released
2 ArduVTOL

ArduVTOL
3 How to analyze a crash?

How to analyze a crash?
4 HD video for UAV's

HD video for UAV's
5 Mapping Mission Ride Along

Mapping Mission Ride Along
6 APM Copter 2.9.1.b has been released

APM Copter 2.9.1.b has been released
7 Arducopter 3Dr or Phantom

Arducopter 3Dr or Phantom
8 ArduVTOL - Wingcopter - Flight Report Nr.1

ArduVTOL - Wingcopter - Flight Report Nr.1
9 Mechanical Hands From A MakerBot: The Magic Of Robohand (From Makerbot blog news)

Mechanical Hands From A MakerBot: The Magic Of Robohand (From Makerbot blog news)
10 NEVER connect a Capacitor backup or voltage protector on APM board

NEVER connect a Capacitor backup or voltage protector on APM board

Contests

Season Two of the Trust Time Trial (T3) Contest has now begun. The fourth round is an accuracy round for multicopters, which requires contestants to fly a cube. The deadline is April 14th.

A list of all T3 contests is here. 

Groups

Advertisement

© 2013   Created by Chris Anderson.   Powered by

Badges  |  Report an Issue  |  Terms of Service