How can we conect the brushless motors to the speed control ?

Hi, recently we bougth 3 brushless motors, a speed control, a rc control, but we dont know how to conect them.

Specifications:

-Motors brushless: Elite series exeed-rc, elite 370 63M02 20-30 kv5400

-Speed Control Bec: 5V/3A NimH 5-12s Lipo 2-4s

-rc control fly sky digital proportional rc system (ct6) 2.4ghz 6 chanels 

-li-po battery Gens 2600mah-25c-11   1v-3s1p (11.1v)

Views: 618

Attachments:

▶ Reply to This

Replies to This Discussion

Permalink Reply by Wesley Chuen on April 30, 2012 at 8:53am

I believe you need 3 Speed controllers for 3 motors.

Permalink Reply by Petrus Botha on April 30, 2012 at 8:53am

What do you wish to do?, it seems you only have one speed controller for three motors, am I correct?

Permalink Reply by Juan Sebastian Otalora Acevedo on April 30, 2012 at 9:14am

we want create a tricopter, when we bougth all  the sellers sayd that we only need 1 speed controls all motors at the same speed

Permalink Reply by Andrew Adams on April 30, 2012 at 9:22am

As far as I know, and I'm no expert, you'll need an ESC for each motor. Connectors. Wire. Control board. Prop spinners. Props etc....

The motors look like inrunners. I've never seen a copter with inrunners either..

Make sure your ESC's and motors are matched as far as current is concerned.

Have you ever flown or built an rc model before?

Permalink Reply by Juan Sebastian Otalora Acevedo on April 30, 2012 at 9:30am
Permalink Reply by Andrew Adams on April 30, 2012 at 9:35am

If you were expecting to build a tricopter with just the stuff listed above, you were mistaken.

Permalink Reply by Juan Sebastian Otalora Acevedo on April 30, 2012 at 9:37am

what would do we need??

Permalink Reply by Petrus Botha on April 30, 2012 at 9:39am

To steer a vehicle like a tricopter you will require differential speed per motor. Same as with a quadcopter or any other multi rotor vehicle. For this you will require one speed controller per motor, and a minimum of three channels, unless you wish to try out tilting motors and vector thrusting.

Permalink Reply by Juan Sebastian Otalora Acevedo on April 30, 2012 at 9:40am

there is a tutorial for this??

we just need somthing simple

Permalink Reply by Petrus Botha on April 30, 2012 at 9:43am

To get started, lets ask the questions

1. Do you have an Ardupilot mega or any other stabiliser system for this tricopter?

Permalink Reply by Juan Sebastian Otalora Acevedo on April 30, 2012 at 9:44am

no

Permalink Reply by Petrus Botha on April 30, 2012 at 9:48am

Ok, Question 2

What is your profeciency level with an RC Helicopter, traditional or multi rotor.

I ask this question only to help me guide you in the right direction

RSS

Social Networking

Top Content 

1 APM Project vs DJI NAZA and WOOKONG

APM Project vs DJI NAZA and WOOKONG
2 APM 2.5 with NEO-6M ublox gps (not 3DR LEA-6)

APM 2.5 with NEO-6M ublox gps (not 3DR LEA-6)
3 APM Copter 2.9.1.b has been released

APM Copter 2.9.1.b has been released
4 Flying 3D Spline Curves between Waypoints with ArduCopter 3.0

Flying 3D Spline Curves between Waypoints with ArduCopter 3.0
5 ArduCopter-3.0 ready for wider use

ArduCopter-3.0 ready for wider use
6 10k autonomous flight - telemetry guided flight, and other APM tests!

10k autonomous flight - telemetry guided flight, and other APM tests!
7 Drone shot down by police

Drone shot down by police
8 MAAT final version is being tested

MAAT final version is being tested
9 Getting ready for Arducopter 3.0

Getting ready for Arducopter 3.0
10 Help Tuning Arduplane 2.73 With A Large Slow Airframe

Help Tuning Arduplane 2.73 With A Large Slow Airframe

Contests

Season Two of the Trust Time Trial (T3) Contest has now begun. The fourth round is an accuracy round for multicopters, which requires contestants to fly a cube. The deadline is April 14th.

A list of all T3 contests is here. 

Groups

Advertisement

© 2013   Created by Chris Anderson.   Powered by

Badges  |  Report an Issue  |  Terms of Service