Moderator

Mission Planner 1.1.74 No longer able to set flight modes?

Since updating my flight mode of Alt hold has changed to Acro. Luckily I spotted this before flying, but now I cannot change it back, it just keeps saying failed to set flight modes, after several restarts and resets it is still not working?

Views: 197

▶ Reply to This

Replies to This Discussion

Permalink Reply by Richard on April 23, 2012 at 1:47pm

Ditto, same problem here

Permalink Reply by Bradley J Carr on April 23, 2012 at 1:52pm

Same here. 

I had some other issues but had to completely reset and start over again and then now I am down to just this one.

Permalink Reply by Ulrich Thiemeyer on April 23, 2012 at 3:02pm
Have the same problem. Now i use an older version...
Permalink Reply by Robert Abbott on April 23, 2012 at 6:35pm

I am having the same problem. " Failed to set flight modes"


3D RoboticsPermalink Reply by Chris Anderson on April 23, 2012 at 7:31pm

I can replicate this. We'll fix it in the next 24 hours.

Permalink Reply by Earl on April 23, 2012 at 8:30pm

The altitude is off by a factor of 10 now ! 10 x too little in the feet mode.

Earl


DeveloperPermalink Reply by Michael Oborne on April 23, 2012 at 9:38pm

i will revert back to .73 when i get home. and sort this out.


ModeratorPermalink Reply by Dean Wynton on April 23, 2012 at 11:40pm

Also not  100% sure if this is MP .74  because I haven`t tested everything, but I would say so? also but compass was out 210 degress on flight data after updating


3D RoboticsPermalink Reply by Chris Anderson on April 27, 2012 at 2:27pm
This is now fixed in 1.1.75
Permalink Reply by Eagle on April 27, 2012 at 6:13pm

I waited to upgrade from 1.1.73 to 1.1.74,,, because I read some threads regarding this problem.

Since...  I updated from 1.1.73 to 1.1.75 and this problem do not exist.

In my humble opinion, dealing with many, many, many version upgrade of APM in a short period of time is to always click "No'" to the update available box... if you have a stable environement working.

Don't get me wrong I do understand why there is so many new versions.... like new Radio Hardware available for telemetry, bug fix, etc...  But keeping a stable environment is (i think) the key to advance successfully in this adventure

Like Chris said... 1.1.75 is available now.

my 2 cents advise.

-Eric

RSS

Social Networking

Top Content 

1 ArduCopter-3.0 ready for wider use

ArduCopter-3.0 ready for wider use
2 APM Project vs DJI NAZA and WOOKONG

APM Project vs DJI NAZA and WOOKONG
3 APM 2.5 with NEO-6M ublox gps (not 3DR LEA-6)

APM 2.5 with NEO-6M ublox gps (not 3DR LEA-6)
4 Flying 3D Spline Curves between Waypoints with ArduCopter 3.0

Flying 3D Spline Curves between Waypoints with ArduCopter 3.0
5 APM Copter 2.9.1.b has been released

APM Copter 2.9.1.b has been released
6 10k autonomous flight - telemetry guided flight, and other APM tests!

10k autonomous flight - telemetry guided flight, and other APM tests!
7 MAAT final version is being tested

MAAT final version is being tested
8 Getting ready for Arducopter 3.0

Getting ready for Arducopter 3.0
9 Help Tuning Arduplane 2.73 With A Large Slow Airframe

Help Tuning Arduplane 2.73 With A Large Slow Airframe
10 How to succeed without really trying

How to succeed without really trying

Contests

Season Two of the Trust Time Trial (T3) Contest has now begun. The fourth round is an accuracy round for multicopters, which requires contestants to fly a cube. The deadline is April 14th.

A list of all T3 contests is here. 

Groups

Advertisement

© 2013   Created by Chris Anderson.   Powered by

Badges  |  Report an Issue  |  Terms of Service