RFD900 Telemetry will not connect in Mission Planner. All settings tried.

Edit: Fix in the comments below

Hi, I've been trying for a few days now and can't figure out these radios. I am using the PX4 platform and when I configure the modems with either the 3DR config tool or the RFD900 Modem tool, the radios seem to connect but never works in Mission Planner or Qground control. I get a time out error, failed to enter command mode or Invalid parameters. I have the Arduplane 2.74 software loaded at the moment.

Some people say they simply use the Mission Planner to upload the firmware and connect without problems.

I have tried this and the radios connect at first with default settings and the terminal has normal text messages showing from the radio. But after I choose the copy required items to remote, the radios no longer allow me to arrange the node ID options and the link is broken with a red and green light both flashing on the radio connected to the PX4. The radio connected via USB serving as a base-node only has a green light flashing.  When I try to load settings via MP or the 3DR tool, the modem settings no longer match after clicking the save settings button. I also get random garbly text from the terminal view:

 

If I turn off the client radio(the non-base node), the scrambled messages stop, but no commands work or anything. The modems appear to respond to terminal commands independantly and while linked together after a fresh firmware flash. But after trying to get things working in Mission Planner, they don't respond to terminal commands unless only 1 is powered on, or the link is not present or attempting to be present.

This is using the Sik on 1.5 RFD900 Firmware. When I use the supplied firmware options v1.2 and v2.2

from the official RFD900 website, I get similar results. The connection initially works from viewing the

LED light statuses but once I try to connect with MP or edit any settings with the integrated radio setup

options, it wont work. I matched the baudrates, net Id's and so on. I do NOT have the USB connected to the Autopilot. But just to add on, the PX4 communicates fine when under USB.

Note: I cannot configure the Node ID's using the 3DR provided firmware. The option does not exist but

somehow the radios manage to connect.

Additionally, I end up having to reflash the firmware because I can no longer load the settings with any modem config tool.

The images I have attached show how the radios look after a flashing the firmware and loading settings.

The second image shows what happens after I copy items to remote and save settings and reload. I do not try to connect the MP flight data until after I attempt to change the settings with the 3DR configuration option. Although I have tried to before and after during my multiple flashings of the firmware, both with the 3DR provided RFD900 firmware and the RFDesign firmware.

There is one last thing. ONLY when I use the v2.2 Sik Firmware from RFDesign's website, if I try to connect via Mission Planner, it will hang for a few seconds, then start to connect. I see the connecting progress/status messages changing a few times and then it just stops in the middle of connecting. Only a few heartbeats and packets get through and then everything stops responding and I have to disconnect.

I'm lost here. Does anyone have any pointers?

Views: 9710

Reply to This

Replies to This Discussion


I just received a bundle of 868 radios from JDrones and had to downgrade the firmware to 1.9. I have the same issue of very slow parameter read and high loss of packets. Link looks solid with 217 RSSI and solid green lights on both ends. Has anyone resolved this issue? MP will also not let me change the receiver values.


T0nimas said:

I am having a little different problem. I can connect but it is very slow and then, when connection is finished the motion in MP is really slow again. I lost a lot of packets I have aprox. 30-40% of link health.

I am trying to connect at 10 meters of the plane.

Setting of my radios: (using RFD900ModemTools.exe)

RFD SiK 1.13 on RFD900P

Baud Rate: 57600

Air Speed: 64

Net ID: 15

Tx Power: 20

Node ID: 2 (but in the SW I can't change it)

Node Destination: 65535 (but in the SW I can't change it)

Min Freq: 868000 (because I am in Europe, and I bought RFD868, however its the same module)

Max Freq: 869000 

Number of chanels: 50

Duty Cycle: 100

Node Count: 3 (but in the SW I can't change it)

ECC, Op Resend, RTSCTS: disabled

Mavlink: Enabled.

The other module has exactly the same parameters.

I tried with ECC adn Op Resend and It doesn't work. I need both disabled to "work" bad.

Have you any ideas about my problem?

Thank you all!

Reply to Discussion

RSS

© 2018   Created by Chris Anderson.   Powered by

Badges  |  Report an Issue  |  Terms of Service