RTF Quad w/ extras

Looking to sell this complete setup.  This is probably the cleanest wiring and the best built quad I have ever seen.  All wires are cut to length and have custom pigtails.  The camera mount shown in the last pic is not included but can found at  http://www.shop.aglhobbiesllc.com/ for a nice setup.  The carbon plates sit on rubber dampening mounts.  I have replaced the stock phillips screws with black hex bolts so they match. The spektrum AR6100E receiver is included but if you dont have spektrum I will take off $35.  Asking $500 shipped.  I am located on a military base and shipping will take a tleast 2 weeks to clear customs and get back into the US FYI. Basically hook up your receiver run through the setup with the GCS and your ready to fly.  Will write the PIDs for easy setup.

Mikrokopter 400mm frame http://www.nghobbies.com/cart/index.php?main_page=product_info&...

4 Pulso motors ($45 each) http://montorc.com/x2212L22.aspx

5 Turnigy 18amp escs (1 extra)

APM v1.0 and Hotel Oil Pan

magnetometer and gps

xbee w/ wire antenna

LED strips on each arm

2 extra arms 1 red 1 black

6 extra props 3 each rotation

extra landing gear

3s 2500mah pack OR  2 1800 saddle packs(your choice)

silver prop spinners and original motor nuts included

 

 

Views: 661

Attachments:

▶ Reply to This

Replies to This Discussion

Permalink Reply by Neil Baker on July 22, 2011 at 9:04am

Email address is w4hfv@juno.com if interested.

Attachments:
Permalink Reply by Casey Levinger on July 30, 2011 at 12:38am

is this still for sale? I would love to get my hands on this one!

Permalink Reply by Neil Baker on July 30, 2011 at 1:28am

Still for sale.  Be happy to send some more pics or answer any questions about it.

Permalink Reply by Casey Levinger on August 2, 2011 at 10:55am
hey neil didn't know if this quad is still for sale or not but i was just wondering what the carrying capacity was. How does it handle the GoPro cam and do you think it could handle something a little heavier? Let me know! Thanks

Casey
Permalink Reply by Denis Duckett on August 3, 2011 at 5:19pm

Neil, were you successful in getting APM v1.0 to Position Hold, and Alt. Hold?

Permalink Reply by Neil Baker on August 4, 2011 at 2:04am

Denis, I have not tried Position hold.  Altitude hold worked but it wasnt as accurate as I thought it would be.  About 5 feet up and then 5 feet down after about 30 seconds. 

Permalink Reply by Neil Baker on August 4, 2011 at 1:50am

Casey, This handles the gopro no problem.  It can probably handle something bigger but a SLR camera might be pushing it.  I put the higher output "L" motors on it which helps.  I strapped 2 4500mah packs to the buttom a while back and it had no problems flying.

Permalink Reply by Ron Jacobs on July 12, 2012 at 12:10pm

Has this been sold?

RSS

Social Networking

Top Content 

1 APM 2.5 from hobbyking

APM 2.5 from hobbyking
2 Alt_hold and loiter acting crazy

Alt_hold and loiter acting crazy
3 Mapping Mission Ride Along

Mapping Mission Ride Along
4 Looking for best laptop screen to see in the sun

Looking for best laptop screen to see in the sun
5 APM Copter 2.9.1.b has been released

APM Copter 2.9.1.b has been released
6 ArduPlane 2.73 released

ArduPlane 2.73 released
7 New micro-cameras emulate insects' compound eyes

New micro-cameras emulate insects' compound eyes
8 Hobby King Ardupilot

Hobby King Ardupilot
9 3 axis Camera Gimble connections.

3 axis Camera Gimble connections.
10 Thirty Days (#17): 12-rotor close up

Thirty Days (#17): 12-rotor close up

Contests

Season Two of the Trust Time Trial (T3) Contest has now begun. The fourth round is an accuracy round for multicopters, which requires contestants to fly a cube. The deadline is April 14th.

A list of all T3 contests is here. 

Groups

Advertisement

© 2013   Created by Chris Anderson.   Powered by

Badges  |  Report an Issue  |  Terms of Service