Simple Arduino Programming Question

Hey guys!

So I am trying to do some very basic arduino programming to master the fundamentals, and something is not working as I expected it to. My board is set up with the PSEL in ESC powere'd mode, and I have a battery source applied to the 3rd input for the time being, and instead of servos, I have LED's hooked up to the 3 output sets. Here is the code:

void setup()
{
pinMode(13,OUTPUT);
pinMode(11,OUTPUT);
pinMode(10,OUTPUT);
}

void loop(){
digitalWrite(13, HIGH);
digitalWrite(11, HIGH);
digitalWrite(10, HIGH);
delay(500);
digitalWrite(13, LOW);
digitalWrite(11, LOW);
digitalWrite(10, LOW);
delay(500);
}

Pin 13 (the board's STAT LED) functions as expected, blinking on and off every second, but OUT2 and OUT3 are solidly lit, no blinking. Why is that? Are they somehow set to PWM by default or something that produces unexpected results? On top of that... the OUT LED's will just turn off after a minute or so, and then not come back on even after a reset, what's up with that? Is there something in frimware that i'm not aware of? (it does the same thing with the jumper across CTRL removed too)

(thanks for the note 13brv3!)

Tags: arduino

Views: 241

Attachments:

▶ Reply to This

Replies to This Discussion

Permalink Reply by Kyle Sanders on April 28, 2009 at 10:13am
thanks a million, that's a great place to start

3D RoboticsPermalink Reply by Chris Anderson on April 28, 2009 at 10:34am
Guys, you've got to refer to the schematic to correspond Arduino pins to ArduPilot-specific nomenclature. It's all there.
Permalink Reply by Reto on April 28, 2009 at 11:33am
Chris, good you link to the schematic here, but as a newbie i am sorry to admit I do not know how I could for example infer from them that ArduPilot servo OUT1 is accessed by programming the D9 pin in the Arduino environment. The 74LS157D "blackbox" in between makes it difficult (if not impossible) to relate the ATmega168 to the OUT pins. You say it's all there, but I couldn't find that connection, although it's probably there. Because of my lack of schematic reading knowledge, I think Michal's overview listing is very usefull.

3D RoboticsPermalink Reply by Chris Anderson on April 28, 2009 at 3:59pm
It's pretty straightforward. Look at the schematic and you'll see that

S1B (which goes to pin 13 on the Atmega) -> Out 1
S2B (pin 14) -> Out 2

Then go to the Arduino pin mapping diagram to see how those physical pins related to Arduino's logical pins. Pin 13 = Digital 9.

It takes a while to learn how to read schematics, but it's worth doing. These are skills that you'll use again!
Permalink Reply by Kyle Sanders on April 28, 2009 at 4:13pm
Ah, thanks for explaining that, it makes alot more sense now. Seeing that i only need an on/off switch, not a PWM'd servo switch, i'll just jump off of one of the other, unused digital pins. Thanks!
Permalink Reply by Reto on April 28, 2009 at 4:32pm
Thanks for all that explanation, Chris. It was not immediately obvious to me, in this part of the ArduPilot diagram around the 74LS157D chip, that S1B (pin3) is to be interpreted as an input which is linked in the chip to 1Y (pin4) output, itself linked to OUT1. But maybe I'm quite lonely finding this not so self-explaining. If this interpretation is right, then I learned again.

3D RoboticsPermalink Reply by Chris Anderson on April 28, 2009 at 4:36pm
A multiplexer (MUX) takes eight inputs in A/B form and switches between them for the output. So S1A and S1B refer to RC vs Autopilot, and the MUX (directed by the Attiny) decides which one gets to control Out 1.
Permalink Reply by Reto on April 28, 2009 at 4:57pm
Thank for this add-on. Now I can imagine a little better how the MUX circuit works in the wires.

RSS

Social Networking

Top Content 

1 APM 2.5 from hobbyking

APM 2.5 from hobbyking
2 Mapping Mission Ride Along

Mapping Mission Ride Along
3 Looking for best laptop screen to see in the sun

Looking for best laptop screen to see in the sun
4 Alt_hold and loiter acting crazy

Alt_hold and loiter acting crazy
5 APM Copter 2.9.1.b has been released

APM Copter 2.9.1.b has been released
6 ArduPlane 2.73 released

ArduPlane 2.73 released
7 New micro-cameras emulate insects' compound eyes

New micro-cameras emulate insects' compound eyes
8 3 axis Camera Gimble connections.

3 axis Camera Gimble connections.
9 Thirty Days (#17): 12-rotor close up

Thirty Days (#17): 12-rotor close up
10 Mechanical Hands From A MakerBot: The Magic Of Robohand (From Makerbot blog news)

Mechanical Hands From A MakerBot: The Magic Of Robohand (From Makerbot blog news)

Contests

Season Two of the Trust Time Trial (T3) Contest has now begun. The fourth round is an accuracy round for multicopters, which requires contestants to fly a cube. The deadline is April 14th.

A list of all T3 contests is here. 

Groups

Advertisement

© 2013   Created by Chris Anderson.   Powered by

Badges  |  Report an Issue  |  Terms of Service