Comment

Comment by ahmed hakeem on November 13, 2011 at 11:43pm

Finally i connected the quadcopter

and everything its ok the Tuning . all motors run same time and all Speed Control Deeps same time

im trying to fly and trying hover the quadcoper like crazily when i try to take off and fail down its like when the gyro set in more sensevety 

i connect the quadcopter with Mission Planer (APM PLANNER)

Then go to (Configuration)  -----> AC2

what must be the numbers there  in Stabilize Roll .. Pitch .. Yaw .. loiter .. ??

when i connected i git this numbers .....Roll and Pitch (p) 4.600 (l) 0.001 (imax) 1.500

Yaw (p) 7.000 (i) 0.010 (imax) 8.0 .... Loiter (p) 0.300 (i) 0.000 (imax) 12.0

 

also Rate Roll and Rate Pitch (p) 0.145 (i) 0.000 (imax) 15.0

Rate Yaw (p) 0.130 (i) 0.000 (imax) 50.0 .... Rate WP (p) 3.000 (i) 0.250 (imax) 20.0

 

That is all when i connect..Did i must Change the Numbers ???

3D Robotics Comment by Chris Anderson on November 12, 2011 at 11:18pm

Adil: Set one of your toggle switch modes to Loiter. Wait for GPS lock, then fly and switch into Loiter at the position you want to hold.

Comment by Adli Shahnaz on November 12, 2011 at 11:09pm

Hello all.

Can somebody help me step by step on how to set the gps hold. Thank you in advance.

 

Comment by brett binnekade on November 9, 2011 at 11:13am

Is it important to mount the board directly in the center of a quad frame or can it be slightly off to the side. I would like to mount mine about 2 or 3cm off center.

3D Robotics Comment by Chris Anderson on November 9, 2011 at 7:56am

Tom: that just means that your throttle is reversed on your RC transmitter (maybe you've switched to another model memory?). Switch it and go through the MP radio setup again.

Comment by ahmed hakeem on November 9, 2011 at 1:33am

hello i m new  in this Group ..also at this quadcopter ..

i receive my ArduCopter Quad v1.1 RTF - i m locking for some one can help me how to fly i have JR-PCM9X but there is no program with this remote only i find :

http://diydrones.com/profiles/blogs/how-to-program-6-flight-modes

this is different model of my remote by the Options ..

if i want to START connect ...

1- which mode i should use airplane or heli ??

2- what is the revers and north ??

3- what should i do in travel adjust ??

4- what should i do in Flap ??

5- what should i do in program Mix i have 1,2,3,4,5,6

6- how can i use the position hold ??

7- how can i use the GPS ??

sorry about this all but really i need help to fly my new babe :)  

Thank For all ...

Comment by Michael Pursifull on November 7, 2011 at 9:12am

See flybrushless.com for other data. The DIYD/jdrones props are not in there, but should give you good comparison datasets to work with. 

Comment by Michael Pursifull on November 7, 2011 at 9:10am

From the jDrones Website 850Kv motor power out put from ESC, 3S LiPo, 10x45 Propeller 25% 50% 75% 100% Amp Wattage Thrust 1 A 11W 170gr 3.4 A 38W 433gr 9 A 100W 855gr 12.2 A 135W 1095gr

880Kv motor power out put from ESC, 3S LiPo, 12x45 Propeller 25% 50% 75% 100% Amp Wattage Thrust 1.5 A 17.5W 230gr 6.1 A 70W 650gr 14.2 A 160W 1290gr 20A A 210W 1380gr

Comment by Jan van Hulzen on November 7, 2011 at 9:06am

Hi,

 

is there information available on the lift characteristics of the arducopter propellers? I am looking for information to use in a theoretical calculation where i am able to relate lift to rpm.

 

thank you for any information

 

Jan

Comment by Dara Shayda on November 3, 2011 at 10:43am

Sorry, I did not mean to name drop.

 

For Canadians they can use these offices to get more info or apply for licenses:

 

http://www.tc.gc.ca/eng/civilaviation/standards/general-recavi-regi... 

 

We will do so since we like to fly for commercial activities.

 

• ‹ Previous
• 1
• …
• 35
• 36
• 37
• 38
• 39
• …
• 45
• Next ›
• Page