Tarrot gimbal screws lost - where to find

Hello,

During one of my flights I've lost one of 2 screws which holds go pro attached to tarot gimbal. Is there any place I can buy it or probably somebody knows a part number to search for on the internet?

Thank you,

Roman

Setting up Channel 8 from the Iris RC xmitter to do a camera trigger

OK, so I've got the Channel 8 assigned in the Pixhawk parameters to perform a camera trigger. But, it would seem that channel 8 is not assigned to any switch on the Iris FSTH9X rc xmitter.

any suggestions on how to assign channel 8 to say the "Gear" s

Iris+ parts

Although I was able to sell the drone, I still have some iris+ parts for sale: 

4 pairs of new props

3 arms (2 black and 1 blue)

1 set of long legs - used

1 set of short legs - new

1 go pro silver

1 fpv black pearl kit with sun shade - only used a couple o

How to modify the Iris+ firmware: eclipse errors and more

Hi,

Sony Action Cam setup for FPV - need ideas for better video xmitter mounting

Iris Forum-

I've been wanting to setup my Sony Action Cam (HDR AS-100V) on my Iris+ and use it as an FPV trainer. I've mounted the camera, inverted, off the front mount, and attached the video xmitter per Colin Guinn's setup video. But I've never like

Iris+ Compass Issue

My Iris+ is still recovering from a serious failure where it plummeted 50m onto rocks on a coastal reef back in September 2015. Three of the four arms were broken as well as top and bottom shell, motors, props, legs, FRsky receiver and other bits inc

GPS Altitude?

I'm not ready to abandon my Iris+ yet because it's still useful, but the detected altitude (and other GPS numbers) change constantly when it's sitting on a table.

I have a bluetooth Garmin GLO that I use in actual airplanes that I put on the same tabl

Suggestion for solvation of the lack of spare parts problem

where can I get iris+ spare motor, props and arm?

Dear all, I went to 3DR site and most items are tag with out of stock or discontinue, can anyone advise how can I still purchase, many thanks

Discovery Buzzer

I am trying to add a discovery buzzer to my Iris+, it is a receiver type, I am very new to the hobby. I have done many searches to find out how. I don't understand. how to program the transmitter for the switch I want to use and the receiver channel

iris+ suddenly started to fall from 80m high and crashed

Hi 

Yesterday I was flying normally and switching between ALT HOLD and LOITER mode back and forth during the mission. 

At the last moment I was at 80m high and was trying to come back, so I switched to ALT HOLD and cut the throttle all the way down. 

It

Have to brag

The Drone Girl, Sally French, just put this article up about me:http://thedronegirl.com  

I mentioned I was active in this forum, that must have missed the cut :)

Happy holidays!

Any Learning configuration of Iris+ (Asia)

Dear All...

I am trying to learn Iris+ more since I have just got my system from a friend.

Any chance of anyone in SouthEast Asia that can discuss with me...

I will have 1 week leave from work for this year and I can travel to your place, currently i am

iris+ water

I was flying my iris+ in a coast cliff and a hard wind caught it and it went strait to the water.. 

when i got there it was bubeling and when i took it out of the water it started to catch on fire... i disconected the battery and it stopped... 

The bod

Camera Tower

Hello comp I can write the parameters in Tower for a camera that is not in the list of 3DR Tower?

3d printed props

Has anyone had success 3d printing propellers?  I am about to start designing a propeller I can print on my reprap printer and wondered if I am re-inventing the wheel...  I haven't found anything suitable for the Iris on Thingiverse  or other similar

Nose orientation is at an angle

After calibrating the compass. My Iris flies with the nose pointed to the right . any ideas how to correct 

Im a newbie . However I think I can present the logs if necessary. Thanks for any tips or resolutions

Thanks  

Help - Gimball and Remote dont link

Guys i got my gimball working and its stable.. but i cant tilt it with my remote... whats wrong? 

Help, First Flight Woes

I just purchased a used Iris+ with gimbal and GoPro3 and FPV. I have downloaded the Tower software to my Samsung Galaxie S5 phone. I have not been able to get the Iris to connect to my phone with the WIFI. I cannot find the wifi signal from the Iris.

Is it true that 3DR is phasing out IRIS+

I heard that that 3DR is phasing out our IRIS+ to focus on the SOLO.

 Is this true? Love my IRIS but Is it time to sell it?