Abolo
  • United Kingdom
Share

Abolo's Groups

Abolo's Discussions

how to connect G-3D Gimbal with pixhawk ?!!

Started this discussion. Last reply by Sam Worthington Jun 9, 2016. 2 Replies

Hello all ,I have G-3D Gimbal controller from walkera and I want to attach it with pixhawk ( actually its chines pixhawk called pixhack ) but it's similar to pixhawk . I tried to connect the wires…Continue

9xTend + pixhawk connection !!

Started Feb 19, 2016 0 Replies

Hello all ,I just get Digi 9xTend 900 Mhz and I want to connect it to my pixhack ( chines pixhawk )…Continue

How to Limit Roll & Pitch stick movement Angle ?

Started this discussion. Last reply by Graham Dyer Dec 27, 2015. 3 Replies

Hi all ,I have problem in controlling my plane with the elevator and aileron when I move to max aileron stick the plane pank with big angle as will as with elevator.this make the flying hard I want…Continue

Is it Problem with Parameters ???

Started Jul 14, 2015 0 Replies

Hi all , I am using mission planner as ground station when I set the flight mods as 1- stabli2- auto3- RTLI get a problem that when I takeoff in stab mod after that i want to change the mode to AUTO…Continue

 

Abolo's Page

Latest Activity

makeflyeasy replied to Abolo's discussion RC plane Parachute tool and configuration in the group ArduPlane User Group
"good work"
Jan 5
Abolo replied to Abolo's discussion Relay switch for Gopro camera !! in the group ArduPlane User Group
"Very good I have to do two separate function 1- power on camera 2- start record , I will use two switches as shown in replays . Now one step done with trigger ,with RC5 How can I assign the second function ? How to do another output throw the RC7 ,…"
Aug 10, 2016
mike de leon replied to Abolo's discussion Relay switch for Gopro camera !! in the group ArduPlane User Group
"yes my friendyou can manual assign do_trigger or let mp do it, its much easier, go to ardupilot and check out mission planner, creating mission, read through it, mp creates a survey grid and assign wp for triggering the camera, makes our job easier,…"
Aug 9, 2016
Abolo replied to Abolo's discussion Relay switch for Gopro camera !! in the group ArduPlane User Group
"I used rc5 as camera trigger and test it from the plane page I works fine , ( I will use this for shatter ) Now I need to Do that command throw waypoint command Second I need another way to output another signal for powerOn the camera also doing…"
Aug 9, 2016
Abolo replied to Abolo's discussion Relay switch for Gopro camera !! in the group ArduPlane User Group
"this relay now not for shutter it's for power the camera on , I will duplicate with another relay for camera shutter ,  using camera trigger will out the needed signal ? Do you mean I don't have to plane it with mission command…"
Aug 9, 2016
mike de leon replied to Abolo's discussion Relay switch for Gopro camera !! in the group ArduPlane User Group
"yes you have to assign it so that pixhawk knows what rc channel pin to trigger, try putting it in rc10 pinout, then go to flight page, right click then camera trigger, but base on yout gopro layout you soldered the wire to power button, afaik there…"
Aug 9, 2016
Abolo replied to Abolo's discussion Relay switch for Gopro camera !! in the group ArduPlane User Group
"no actually I expect output as do set servo command !! "
Aug 9, 2016
mike de leon replied to Abolo's discussion Relay switch for Gopro camera !! in the group ArduPlane User Group
"idk about the kill switch how it works, base on your layout its correct, it should trigger the relay if ever 5v is send by the kill switch, did you go to mission planner>initial setup>optional hardware>camera, on the lower part assign which…"
Aug 8, 2016
Abolo replied to Abolo's discussion Relay switch for Gopro camera !! in the group ArduPlane User Group
"I just get rcexl opto gas engine kill switch v2.0 which use for cut off the engine pdf manual I use it with the receiver X8R and connect it to relay (Meisei m4-5h) and it works fine and the relay work fine . as shown in the pic Now I try to send the…"
Aug 8, 2016
Hans H. replied to Abolo's discussion Relay switch for Gopro camera !! in the group ArduPlane User Group
"Try the IC that is made for this. The "CD4066" is a "CMOS QUAD BILATERAL SWITCH". You can get 5 for 1USD on Ebay. Read the datasheet: https://www.fairchildsemi.com/datasheets/CD/CD4066BC.pdf "
Aug 8, 2016
mike de leon replied to Abolo's discussion Relay switch for Gopro camera !! in the group ArduPlane User Group
"get a turnigy relay switch"
Aug 7, 2016
naish replied to Abolo's discussion Relay switch for Gopro camera !! in the group ArduPlane User Group
"No it's not... that relay uses about 35mA to drive the coil. If you get that current straight from the Pixhawk I/0 pin you will damage the Pixhawk. You need to use a transistor or a Solid state relay. "
Aug 7, 2016
Abolo replied to Abolo's discussion Relay switch for Gopro camera !! in the group ArduPlane User Group
" "
Aug 6, 2016
Abolo replied to Abolo's discussion Relay switch for Gopro camera !! in the group ArduPlane User Group
"I already open the Gopro and get out two wires for power switch just need to connect it to relay to operate throw Pixhawk The camera has it's own power throw it's battery , the relay function is just switch to close for 3 second and…"
Aug 6, 2016
Michael Ciurescu replied to Abolo's discussion Relay switch for Gopro camera !! in the group ArduPlane User Group
"If you don't want to open the GoPro and risk damaging it, there is a way to control it using the HD bus port. If you google for "gopro hd bus", you can find a lot of sites showing how to control the GoPro using the HD bus, for…"
Aug 5, 2016
naish replied to Abolo's discussion Relay switch for Gopro camera !! in the group ArduPlane User Group
"@ Abolo No you won't damage the Gopro, but you will damage the pixhawk as a relay will use more than the allowed 15mA you can get from the I/O pins.  You have to use a solid state realy like…"
Aug 4, 2016

Profile Information

About Me:
student and I like hoobe flying
Please tell us a bit about your UAV interest
i like flying
Hometown:
London

Comment Wall

  • No comments yet!

You need to be a member of DIY Drones to add comments!

Join DIY Drones

 
 
 

© 2017   Created by Chris Anderson.   Powered by

Badges  |  Report an Issue  |  Terms of Service