Anders Wikstrom
  • Male
  • Ostergotland
  • Sweden
Share

Anders Wikstrom's Friends

  • Dan Benson
  • AndyL
  • Nathan Jones
  • Michael Oborne

Anders Wikstrom's Groups

Anders Wikstrom's Discussions

Cannot arm with CUAV M8N GPS

Started Jul 24, 2016 0 Replies

This has been reported in Github!I am using a few CUAV M8N GPS receivers as the M8N chip is great!With the Rover code there is no problem to arm but the plane totally refuses to arm. It says GPS1…Continue

Cannot arm with CUAV M8N GPS

Started Jul 24, 2016 0 Replies

This has been reported in Github!I am using a few CUAV M8N GPS receivers as the M8N chip is great!With the Rover code there is no problem to arm but the plane totally refuses to arm. It says GPS1…Continue

Cannot arm with CUAV M8N GPS

Started Jul 24, 2016 0 Replies

This has been reported in Github!I am using a few CUAV M8N GPS receivers as the M8N chip is great!With the Rover code there is no problem to arm but the plane totally refuses to arm. It says GPS1…Continue

Vehicle changes

Started this discussion. Last reply by Anders Wikstrom Jan 7, 2016. 7 Replies

Dear MichaelHappy New Year!Mission Planner is really awesome and I love it.I have tried to mention this before but still MP shows some strange behavior sometimes.Currently USB-connected to Pixhawk…Continue

 

Anders Wikstrom's Page

Latest Activity

Anders Wikstrom replied to Nathan Jones's discussion Standard Settings for PixHawk Rover Skid Steering + Sabertooth in the group ArduRover User Group
Oct 16
Anders Wikstrom replied to Nathan Jones's discussion Standard Settings for PixHawk Rover Skid Steering + Sabertooth in the group ArduRover User Group
"It seems very strange!I can check this next week when I'm back if no other has helped with this.Althogh I use Graupner there should be no difference. Port 1 and 3 are connected in my setup. To give you all info i have to connect to the system…"
Oct 16
Anders Wikstrom replied to Peter Gerber's discussion Pixhawk Lite V2.4.6 Controlling problems in the group PIXHAWK
"It can also be caused by plastic propellers. Try carbon fiber ones. They are far stiffer. That can make a huge difference. AndersSweden"
Oct 4, 2016
Anders Wikstrom replied to Steve Bramah's discussion telemetry problems in the group PIXHAWK
"3DR has a utility 3DRadio.exe. It's a free software to talk to the radios over USB.Make sure the Baud-rate is correct (and the same) for radio and controller in the vehicle end and the radio and Mission planner in the other (local) end.All…"
Sep 13, 2016
Anders Wikstrom replied to Cala's discussion New generation Esc to update? in the group ArduCopter User Group
"It should be no problem but be aware that there is no BEC. That means they will not power your controller and receiver. If you have a separate BEC that's fine. Why not buy one and test? Anders Sweden"
Sep 12, 2016
Anders Wikstrom replied to John's discussion a Powerful Robust Antenna tracker using the Pixhawk and Mission Planner
"1. You set this in the configuration as SERVO_XXX_TYPE where XXX is PITCH or YAW 2. As above 3. The Pixhawk is to move as the antenna. Otherwise acc and gyros will not work. If the attached GPS has a compass it should be placed to move with the…"
Aug 29, 2016
Anders Wikstrom posted discussions
Jul 24, 2016
Anders Wikstrom replied to Lane Barry's discussion Dual Motor Drive Boat(Rover) setup in the group ArduRover User Group
"No! Two motors on each side connected in parallel. Turning means that the motors on one side have different speed or direction than on the other side. A boat would run quite equally without any rudder. Adding a rudder would add complexity."
Jun 30, 2016
Anders Wikstrom replied to Doug Walmsley's discussion Does ArduRover Support 6-Wheeled Rocker-Bogie Vehicles? in the group ArduRover User Group
"I have seen your pictures and the movie. How do you intend to steer? If your rover can use skid-steering all you have to do is connecting all motor on each side to the same output. For DC-motors you can have one driver and connect the motors in…"
Jun 29, 2016
Anders Wikstrom replied to Lane Barry's discussion Dual Motor Drive Boat(Rover) setup in the group ArduRover User Group
"It can't be different than the rover! Channel 1 & 3 as on the rover and the same setup.Map the outputs of your transmitter or the pixhawk so it works as you want.There should be no problem doing this! I run my rover with one stick.…"
Jun 29, 2016
Anders Wikstrom replied to Warren Purnell's discussion Copter yaw orientation changes when Modes changed in the group ArduCopter User Group
"How about the throttle? I regularly switching modes without problems. It appears that your copter want to descend. You may have to post your log, then someone can probably help you. Anders"
Jun 7, 2016
Anders Wikstrom replied to Hugues's discussion Ardurover former wiki documentation available ? in the group ArduRover User Group
"You have run into the same issue I saw.Arming has been integrated in the Rover but not correctly. You have two options: Arm the rover. It should work Set ARMING_REQUIRED to False (0) Anders"
May 22, 2016
Anders Wikstrom replied to Hugues's discussion Ardurover former wiki documentation available ? in the group ArduRover User Group
"Servos has to be connected to Port 1 and Port 3 in Skid Steering Anders"
May 21, 2016
AndyL left a comment for Anders Wikstrom
"Just sent u my rover's wiring schmatics."
May 5, 2016
AndyL left a comment for Anders Wikstrom
"Rover%20wiring.pdf"
May 5, 2016
AndyL left a comment for Anders Wikstrom
"Pls email sketch to Lowe_andy@yahoo.com. Thanks."
May 5, 2016

Profile Information

About Me:
Musician
Photographer
Quad- and soon OctoCopter flyer
IT-Professional
Please tell us a bit about your UAV interest
Building a OctoCopter based on a
Tarot IRON Man T100 Frame
PixHawk
Graupner Mz-24
Hometown:
Norrköping

Comment Wall (3 comments)

At 7:12am on May 5, 2016, AndyL said…

Pls email sketch to Lowe_andy@yahoo.com. Thanks.

At 7:17am on May 5, 2016, AndyL said…
At 7:17am on May 5, 2016, AndyL said…

Just sent u my rover's wiring schmatics.

You need to be a member of DIY Drones to add comments!

Join DIY Drones

 
 
 

© 2017   Created by Chris Anderson.   Powered by

Badges  |  Report an Issue  |  Terms of Service