"the plane nees to be over a minimum ground speed to start the motor."
Andres Lill's Discussions
Flight modes setting
Started this discussion. Last reply by Michael Oborne Aug 23, 2012. 6 Replies 0 Likes
Hello from Estonia, I have a ARM 2, and at moment not understand one thing.On Mission Planner 1.2.7 I programmed flight modes (mode 1=manual, mode 2=stabilize, mode 3=RTL, mode 4=auto, mode…Continue
Andres Lill's Page
Latest Activity
Andres Lill replied to Andres Lill's discussion Flight modes setting"Note: As a safety measure, your throttle will only arm on the ground in Manual mode, Stabilize or for an autotakeoff in Auto mode. It will not come in in any other Auto mode until you are in motion in the air.
I found this note from manual,…"
Andres Lill replied to Andres Lill's discussion Flight modes setting"Today I made the tests outside room,but nothing. ARM locked GPS, then I went approx 135m away from place, where GPS locked ,switched RTL function, but no reaction, engine doesn`t start rotateing.Maybe airplane must to be on the air with…"
Andres Lill replied to Andres Lill's discussion Flight modes setting"Hi Rui Manuel, great thanks for good ideas.Yes, i tryd inside room and GPS was not locked.Today after work, I will make new experiences outside room.I hope, I get solutions for my problem and I will report here about results. "
Rui Manuel Cravo Marques replied to Andres Lill's discussion Flight modes setting"Hi Andres, I'm not ArduPlane specialist (I only fly ArduCopter), however, in Arducopter software, Auto modes like loiter, RTL and auto, only work if you have GPS lock. If you are trying this at home, maybe you don't have gps lock and RTL…"
Andres Lill replied to Andres Lill's discussion Flight modes setting"Some additions more, on Mission Planner 1.2.7, on StandardParams option, Short failsafe action (FS_SHORT_ACTN)=ReturntToLaunch, Long faisafe action (FS_LONG_ACTN)=None, GCS "
Andres Lill posted a discussionFlight modes setting
Hello from Estonia, I have a ARM 2, and at moment not understand one thing.On Mission Planner 1.2.7 I programmed flight modes (mode 1=manual, mode 2=stabilize, mode 3=RTL, mode 4=auto, mode 5=circle, mode 6=manual).I use Turnigy 9x transmitter with three position switch.I made my tests in room, on my hands.When I switch to stabilize mode, the airplane engine start running (at throttle min. value 60, setting on ArduPlane Pids option) and elevator, ailerons and rudder are moveing on right…See More
Andres Lill replied to Michael Bojsen's discussion Missing overlay on GoPro Hero2 signal with MinimOSD"Now my ARM2 works! I updated firmwares for ARM and OSD and its OK now.Yes. home direction arrow and home distance icon appears to screen when GPS signals founded and locked.
Thanks Michael!"
Andres Lill replied to Michael Bojsen's discussion Missing overlay on GoPro Hero2 signal with MinimOSD"Oh sorry, yes, there is Arduplane v2.50 and I uploaded it"
Andres Lill replied to Michael Bojsen's discussion Missing overlay on GoPro Hero2 signal with MinimOSD""Have you upgraded the firmware on the minimosd? If you have upgraded to 2.40 on your APM2 you should make sure that the minimosd is using the firmware with mavlink1.0"
Michael, did You mean, that I must install to my PC…"
Andres Lill replied to Michael Bojsen's discussion Missing overlay on GoPro Hero2 signal with MinimOSD"I use Mission Planner 1.2.2 mav 1.0 and ArduCam OSD Config-By Michael Oborne 0.5.4425.14358. Yes, I upgraded firmwares several times, but now not sure, doing I right.
I upgraded OSD with MinimOSD_19_MAV10.hex…"
Andres Lill replied to Michael Bojsen's discussion Missing overlay on GoPro Hero2 signal with MinimOSD"Hi Michael and thanks to answer.At first I thinked this, I tryd it outside room, the GPS signal fixed, but home direction and distance missing and longnitude and latidude values was zeros."
Andres Lill replied to Michael Bojsen's discussion Missing overlay on GoPro Hero2 signal with MinimOSD"Hello from Estonia, I was looking, on Your OSD layout, there is missing home direction arrow and home distance icon.I started built up my FPV airplane too and have a ARM 2 +minimosd.And here is the same problem, .On ArduCAM OSD Config tool (on…"
Profile Information
- About Me:
- Interested about rc airplanes
- Tell us a bit about your UAV interest
- Very interested
- Hometown:
- Viimsi
Comment Wall
- No comments yet!
Social Networking
Top Content
Contests
Season Two of the Trust Time Trial (T3) Contest has now begun. The fourth round is an accuracy round for multicopters, which requires contestants to fly a cube. The deadline is April 14th.A list of all T3 contests is here.
Groups
-
Melbourne
47 members
-
Moderators
24 members
-
ArduCopter Italian Group
87 members
-
Andropilot Users Group
183 members
-
ArduPlane User Group
692 members
Advertisement
© 2013 Created by Chris Anderson.
Powered by
