Bernardo
  • Male
  • RhlPflz
  • Germany
Share

Bernardo's Friends

  • Miguel
  • André Fernandez
  • garland jackson
  • Siyan
  • FerrosonicFPV
  • JUAN JIMENEZ
  • Rafael Córdoba
  • Faraz Ahmad
  • Andrew Tridgell

Bernardo's Groups

Bernardo's Discussions

Mission Planner latest version

Started this discussion. Last reply by Bernardo Feb 17. 2 Replies

Hi,today I actualized my version of MP on the PC.Then I found that the FULL PARAMETER LIST is gone.The FULL PARAMETER TREE is also not visible in the menue.Is it just me or is the MP version 1.3.44…Continue

burning wires in COMPASS_MOT calibration !

Started this discussion. Last reply by Ravi Jul 25, 2016. 8 Replies

Hi,during the COMPASS_MOT calibration I burned the wires with the DF13 plugs from the PM to the Pixhawk.I'm lost because it is the second time this happened with two different FC on the copter.I'm…Continue

Tags: Pixhawk, plug, to, wires, module

DISARM_DELAY where is that option now? cant'find it!

Started this discussion. Last reply by Bernardo Jan 17, 2016. 1 Reply

hi,trying to setup a new copter with Pixhawk FC and mission planner I realized that the option *DISARM_DELAY* is not available ??????The 3 or 4 seconds idling after arming and after landing are way…Continue

External vs. internal compass (PixHawk v.2.4.6) Help neede with config and compass variance (/inconsistency)

Started this discussion. Last reply by Channel Islands Aug 28, 2016. 33 Replies

Hi,happy New Year , one and all :) !now upgraded from 3DR APM2.5 to a PixHawk FC.Have 3D (GPS) lock.The compass calibration is the same as with the ol'good APM, the difference is I see two…Continue

 

Bernardo's Page

Latest Activity

Bernardo commented on Klaus Heinrich's group PIXHAWK
"@ James Miller: Perhaps the power of the USB is too low. Try connect the Pixhawk with a short cable direct to an USB plug (?) or try a different cable"
Jan 11
Bernardo commented on Laser Developer's blog post LW20 LiDAR - half the size, twice the performance, infinitely better.
":) great tech specs! following up the final version and release date ;)"
Dec 7, 2016
Bernardo replied to Cala's discussion Video streaming using UVC device in the group Tower (Droidplanner)
"This is a cool feature. But I'm wondering if that only works for the 3DR SOLO ??? I tried to get video on the Tower App (v.4.0) but when I connect the telemetry (433MHz) over the OTG USB hub, the Tower App shuts down (disconnect) every…"
Nov 29, 2016
Bernardo commented on Luis Vale Gonçalves's blog post ArduPilot: Copter 3.4.1 released
"Got it :)  Thank you for the clarification, Luis"
Nov 23, 2016
Bernardo commented on Luis Vale Gonçalves's blog post ArduPilot: Copter 3.4.1 released
"Cool! :) This new version promises interesting new features to try and to enjoy for our copter hobby :D A biiig *THANK YOU* to the developers ! Two questions I have: Is there a way to download the v.3.4 in the .msi   format too ??? (as…"
Nov 22, 2016
Bernardo left a comment for Faraz Ahmad
Sep 18, 2016
Bernardo left a comment for Faraz Ahmad
"To use this sonar on APM or on a Pixhawk, you need the version with two boards for the signal conversion. Then configure in Mission Planner (kind of calibration). That is all."
Sep 18, 2016
Bernardo replied to Hugues's discussion How to assign a receiver channel as a pass-thru Pixhawk ? in the group ArduCopter User Group
"Thank you for the link. Interesting post there with lot of info :) Hope to enlighten me there"
Sep 13, 2016
Channel Islands replied to Bernardo's discussion External vs. internal compass (PixHawk v.2.4.6) Help neede with config and compass variance (/inconsistency)
"Hi Bernardo Your int compass is probably damaged I exactly had the same issue with 2 differents Pixhawk whom experiment by misfortune few crash. Even by disabling the Internal, still had Error Pos Vert Variance and Error Compass Variance (Full Red…"
Aug 28, 2016
Bernardo replied to fabio alberto figueroa benitez's discussion construction of a drone
":) welcome to the world of ideas, projects and multi-copters. the best place to start is reading the wiki. it is complete, well researched and a very good source of info. we have a superb wiki !  :D"
Jul 26, 2016
Ravi replied to Bernardo's discussion burning wires in COMPASS_MOT calibration !
"remove the Vcc and GND wire form the compass JST connector. looks like your Vcc and GND wires are reversed on compass. I assume that you are using a Compass amd GPS combo."
Jul 25, 2016
Bernardo replied to Bernardo's discussion burning wires in COMPASS_MOT calibration !
"ok, found the cause of the problem: the hint with the "poor ground connection" is right, It was even worse. Due to a crash into an apple tree one or more motors continued spinning for a while (perhaps  RTL). That burned the main…"
Jul 25, 2016
Bernardo replied to Bernardo's discussion burning wires in COMPASS_MOT calibration !
Jul 23, 2016
Bernardo replied to Bernardo's discussion burning wires in COMPASS_MOT calibration !
Jul 23, 2016
Bernardo replied to Bernardo's discussion burning wires in COMPASS_MOT calibration !
"It is the PM that is delivered with the Pixhawk or the CUAV FC. So they're too weak for 6S. @Andre = I don't understand the ESC thing. I have (hexacopter) ESC with two wires (gnd and signal). How that could fry the ground wires between the…"
Jul 23, 2016
Andre K. replied to Bernardo's discussion burning wires in COMPASS_MOT calibration !
"Village=voltage (the crappy mobile version does not allow edit)"
Jul 22, 2016
Andre K. replied to Bernardo's discussion burning wires in COMPASS_MOT calibration !
"You have a huge gnd resistance causing village drop between PM and at least one ESC. Then the negative is traveling thru PM and ESC wire. Fix the poor gnd connection, and\or remove ground loop by disconnecting pwm Ground and +5v"
Jul 22, 2016
Mossbackfarm replied to Bernardo's discussion burning wires in COMPASS_MOT calibration !
"Many power modules don't support 6S...is it an attopilot, or (maybe) the HK module?"
Jul 22, 2016
Bernardo posted a discussion

burning wires in COMPASS_MOT calibration !

Hi,during the COMPASS_MOT calibration I burned the wires with the DF13 plugs from the PM to the Pixhawk.I'm lost because it is the second time this happened with two different FC on the copter.I'm using 6S Lipo and a PM that reads DC in 2S - 7S - 5.4V, 3AIt looks (pic) the two ground wires smoked most.Please- I could use a hint on whats my error is. The copter formerly flies, it is a rebuild.See More
Jul 22, 2016
Bernardo replied to herve pellarin's discussion ultrasonic HC-SR04 suitable for arducopter?
"Hi :) ok, today i can inform that the module works now! Pin 14 did it. Many thanks to Juan - you lead me to success :D (YAY!!! ) :D"
Jun 24, 2016

Profile Information

About Me:
found a new cool outdoor hobby where I can take photo und video from a new perspective and get involved a little into modeling (and electronics) :D
Please tell us a bit about your UAV interest
Building my second hexa :)
690Tarot 13" prop 6S 18 minutes (+-2)flight APM2.5 now PixHawk
650kV
700 Hexa 15" prop 6S under construction CUAV 2MB
380kV
Hometown:
Dierdorf

Bernardo's Photos

Loading…
  • Add Photos
  • View All

Comment Wall

  • No comments yet!

You need to be a member of DIY Drones to add comments!

Join DIY Drones

 
 
 

© 2017   Created by Chris Anderson.   Powered by

Badges  |  Report an Issue  |  Terms of Service