Cristian Rougier
  • Male
  • Distrito Federal
  • Mexico
Share Twitter

Cristian Rougier's Groups

Cristian Rougier's Discussions

Hardware needed

Started Feb 5 0 Replies

Hello how are you?I purchased year ago, one quadcopter in china (pictures below). with a 2.4 ghz manual control.I need to use this for aereal photography, but i need the folowing:- GPS- GPS based…Continue

 

Cristian Rougier's Page

Latest Activity

Cristian Rougier replied to Cristian Rougier's discussion Motor spin slow than others in the group ArduCopter User Group
"Thank you for your answer. I erase from CLI  and the problem persist, i will try with early version. Regards"
May 2
OG replied to Cristian Rougier's discussion Motor spin slow than others in the group ArduCopter User Group
"No just erase the flash on the APM in CLI mode. Then reload the software from scratch in the mission planner do not import your old setting enter them manually if you can remember . Your…"
May 2
Cristian Rougier replied to Cristian Rougier's discussion Motor spin slow than others in the group ArduCopter User Group
"Hello, and thank you for your answer. I do this, and yes, motors work fine directly to throttle channel.I need to return my APM for warranty? or what can i do?"
May 2
OG replied to Cristian Rougier's discussion Motor spin slow than others in the group ArduCopter User Group
"Hello, I removing the APM from the picture to make sure it not the motors & ESC. plug the each ESC directly in to the throttle Chanel of the receiver. To see if each motor spin up normally when you apply…"
May 1
Cristian Rougier added 2 discussions to the group ArduCopter User Group
Apr 30
Cristian Rougier replied to Cristian Rougier's discussion Motor spin slow than others in the group ArduCopter User Group
"HELLO i checked in status and channel 4 output is lower than other channels. I tested in low and high speed, Please see the attached images. Can you help me to correct this please? Regards Cristian"
Apr 30
Cristian Rougier replied to Cristian Rougier's discussion Motor spin slow than others in the group ArduCopter User Group
"I changed all ESC's to CX-ESC-40A , and the problem persist, motor 4 spin slow "
Apr 30
Guillaume Braibant replied to Cristian Rougier's discussion Motor spin slow than others in the group ArduCopter User Group
"Hello, I had the same problem and here's some tips to get it fixed. 1. Verify the motors connections and ESC calibrations (If it seems ok for you, go to the second step). 2.  With Mission Planner, look at the artificial sight and check…"
Apr 30
Jason Till replied to Cristian Rougier's discussion Motor spin slow than others in the group ArduCopter User Group
"I had a similar issue it was just the apm in stabilise mode trying to work out level as soon as the copter leaves ground it applies full power to all motors and adjusts itself to correct level. In the manual for your first test flight attach props…"
Apr 30
Cristian Rougier replied to Cristian Rougier's discussion Motor spin slow than others in the group ArduCopter User Group
"Hello all if i change the output s3 to s4  (and s4 to s3) now motor 3 work bad and 4 fine, so may be the ESC ? is a new Hobbywing Skywalker Quattro 20A x4 I repeat that all motors work fine in calibrate ESC mode single or automatic. Im testing…"
Apr 29
Cristian Rougier replied to Cristian Rougier's discussion Motor spin slow than others in the group ArduCopter User Group
"Hello, thanks you for you reply,connection between the ESC & motor are ok, because when i calibrate ESC's all motors work fine, but when i arm this motor 4 spin less than others, less force, i can stop the motor with my finger at medium…"
Apr 29
Warren Purnell replied to Cristian Rougier's discussion Motor spin slow than others in the group ArduCopter User Group
"I find that on spool up prior to takeoff one motor may spool slower. Once at takeoff speed and as it leaves the ground all is OK."
Apr 29
OG replied to Cristian Rougier's discussion Motor spin slow than others in the group ArduCopter User Group
"Sounds like the connection between the ESC & motor is bad remove bullets & join connections directly together. setup your motors & ESC in CLI mode. turn on radio first set throttle to max power on copter to program ESC REMOVE PROPS !!"
Apr 29
Tono replied to Cristian Rougier's discussion Motor spin slow than others in the group ArduCopter User Group
"have you calibrated the accelerometer?"
Apr 29
Shyam Balasubramanian replied to Cristian Rougier's discussion Motor spin slow than others in the group ArduCopter User Group
" I have a similar issue with my quad. Any solution out there yet?"
Apr 29
Charlie Fox replied to Cristian Rougier's discussion Motor spin slow than others in the group ArduCopter User Group
"When I bench test my octocopter I have a similar issue. But with props on testing while under the restraint of my hand It's fine. I think its just the apm trying to work out what is happening and slowing a motor down to try get some sensor…"
Apr 29

Profile Information

About Me:
Manager of cartomex.com
Tell us a bit about your UAV interest
Aerial Pictures, video and LIDAR
Hometown:
Mexico City

Comment Wall

  • No comments yet!

You need to be a member of DIY Drones to add comments!

Join DIY Drones

 
 
 

Social Networking

Contests

Season Two of the Trust Time Trial (T3) Contest has now begun. The fourth round is an accuracy round for multicopters, which requires contestants to fly a cube. The deadline is April 14th.

A list of all T3 contests is here

Groups

Advertisement

© 2013   Created by Chris Anderson.   Powered by

Badges  |  Report an Issue  |  Terms of Service