GIREESH NARAYANAN NAIR
  • Male
  • COIMBATORE, TAMIL NADU
  • India
Share Twitter

GIREESH NARAYANAN NAIR's Friends

  • shanthosh ravikumar

GIREESH NARAYANAN NAIR's Groups

 

GIREESH NARAYANAN NAIR's Page

Latest Activity

GIREESH NARAYANAN NAIR commented on Chris Anderson's group ArduCopter User Group
"Thanks Randy Your suggestion worked. I loaded AC2.9.1b to my APM1.4 and my Quad is back to flying."
Aug 31, 2013
GIREESH NARAYANAN NAIR commented on Chris Anderson's group ArduCopter User Group
"How I can get software version : 2.9.1 for APM 1.4. It is no longer supported. "
Aug 29, 2013
GIREESH NARAYANAN NAIR left a comment for Devon Lyons
"Software version 2.9.1 is no longer supported by DIY Drones forum. How can I get Firmware for Older versions of Mission Planner. For new versions(1.2.67) whether GPS lock is mandatory for arming ? My board is getting armed without moving throttle…"
Aug 18, 2013
Charles lakins replied to GIREESH NARAYANAN NAIR's discussion Ardupilot 1.4 Arming Problem in the group ArduCopter User Group
"gps lock may be required also sometimes without it having a lock, it will arm spin up, then disarm ,a reboot will be needed before arming again   having a lock prevents that from happening you can disable checks but you shouldn't do that…"
Aug 17, 2013
Bo Barry replied to GIREESH NARAYANAN NAIR's discussion Ardupilot 1.4 Arming Problem in the group ArduCopter User Group
"I have the same problem & get a AP_MOTORS error on startup in terminal mode. ESC cal doesn't work. By Googling a lot I found a comment about RADIO CALIBRATION needed to be done. I thought I had done that but plan to recheck tomorrow. Stuck…"
Aug 16, 2013
Earl replied to GIREESH NARAYANAN NAIR's discussion Ardupilot 1.4 Arming Problem in the group ArduCopter User Group
Aug 16, 2013
GIREESH NARAYANAN NAIR added a discussion to the group ArduCopter User Group
Thumbnail

Ardupilot 1.4 Arming Problem

I am new to this groupI was using Ardupilot1.4 board for my Quad and it was flying well. Recently I made some modification in frame and reprogrammed the board with Mission Planner 1.2.67 Version. Caliberation of accelerometer and Radio done. But I was unable to arm the board after that.No changes made in electronics.Earlier I was using MP Version 1.12.32.Can anybody help me solving this arming problem?See More
Aug 16, 2013
Charles lakins replied to GIREESH NARAYANAN NAIR's discussion Arming Problem with Ardupilot Mega1.4 in the group ArduPilot (legacy) User Group
"i'm not familiar with the mega 1.4 this group is for the legacy board that doesn't support multirotors I also have a apm2.5 and with it you should have a gps lock before arming also your trims need to be correct for the arm to work right"
Aug 15, 2013
GIREESH NARAYANAN NAIR added a discussion to the group ArduPilot (legacy) User Group
Thumbnail

Arming Problem with Ardupilot Mega1.4

I am new to this group. I was using Ardupilot Mega 1.4 for my Quad and it was working reasonably well. I made some frame modification and programmed the board with APM Planner 1.2.67. Then the accelerometer caliberation, radio caliberation completed successfully. But when I tried to arm the quad it was not getting armed. I tried almost every thing I know but could not get it armed, some thing is going wrong.Can anybody help me? See More
Aug 15, 2013
GIREESH NARAYANAN NAIR commented on Kevin Hester's group Andropilot Users Group
"I need a help, I am new in Ardupilot Group I developed a quad copter using Ardupilot1.4 board and flying reasonably well. This week after doing some structural modification I reprogrammed the board with latest APM software 1.2.67 version,…"
Aug 14, 2013

Profile Information

About Me:
20 Years as Airman in IAF. Now working as Senior Technical Assistant in Aerospacs Department, Amrita School Of Engineering (Amrita Viswa Vidya Peetham University)
Please tell us a bit about your UAV interest
After joining ASE, I was given charge of Flight Testing Lab. Since then involved with students with various experimental projects. I built one Quad copter and one FPV UAV, test flights done and till in the process of fine tuning them. New in this field (02 years)
Hometown:
KOTTAYAM, KERALA, INDIA.

Comment Wall

  • No comments yet!

You need to be a member of DIY Drones to add comments!

Join DIY Drones

 
 
 

© 2014   Created by Chris Anderson.

Badges  |  Report an Issue  |  Terms of Service