"Dani - Do you have time to look at the attached Excel file for making custom frame calculations and creating the add_motor_raw commands? I'm looking to create a document that tells custom frame folk how to use arducopter.
Please look at…"
Jeff E's Discussions
Mission Planner option for INPUT voltage
Started this discussion. Last reply by Jeff E Aug 21, 2011. 1 Reply 0 Likes
Is there a way or is possible to be added on the mission planner to set this? # define INPUT_VOLTAGE X.XXSo that correct voltage will show on ArduStation/Mission Planner without uploading via…Continue
Could this be a bad APM IMU or the ATMEGA board is having issues?
Started Jul 21, 2011 0 Replies 0 Likes
I recently purchase a Arducopter frame kit with motor esc. I have a previous board that was working well on 2.0.35 but the frame had been damaged so i moved it to the Arducopter frame. - APM hardware…Continue
Tags: 2.0.37, atmega2650, imu, oilpan, damage
Could this be a faulty ESC?
Started this discussion. Last reply by Jeff E Jul 20, 2011. 2 Replies 0 Likes
I recently bought from a local reseller here a complete kit of arducopter. It turns out it was an old model with 1280 board and now after soldering it seems the esc is damaged. I tried to swap…Continue
Clarification on MediaTek MT3329 GPS
Started this discussion. Last reply by Jeff E Jul 16, 2011. 1 Reply 0 Likes
I have this GPS from udrone. I tried the MTK Mini GPS to check the refresh rate and…Continue
Jeff E's Page
Latest Activity
Wayne Jones replied to Jeff E's discussion Arducopter Support for uneven Hexa TY6 H6"Hey, if possible can a idiot proof example of how to write the code for the above V-6 hexa be shown here. I get the percentages from 100% arm length and how to figure that to fit my frame, what I don't get is exactly how to write the code and…"
Jeff E commented on Bill Nesbitt's blog post AutoQuad ESC32 v1r5"I have used castle ESC for a long time, even both their esc that were still version 1 and got replaced to whatever revision but had to ship it back (Im outside US so its a bit expensive). IMHO unless castle will replace the existing HW and then…"
Jeff E commented on Bill Nesbitt's blog post AutoQuad ESC32 v1r5"Magnus, TC made those ESC but only for himself, he said that useless to create such ESC since most Hobbywing OEM will perform well with simonk firmware. OPESC still no word when they will release but I know they are testing. Sadly like ESC32 still…"
Jeff E commented on Bill Nesbitt's blog post AutoQuad ESC32 v1r5"Nice....I envy you since I dont have the means to make one but would like to get a cheap one like ESC32 or the AfroESC which TC stop making. HerKules II is out of budget. So I am stuck in waiting :(
"
Jeff E commented on Bill Nesbitt's blog post AutoQuad ESC32 v1r5"Davey, have you checked TC's AfroESC he dont mind someone building it, its opensoruced but not based on STM32 ARM but rather the normal ATMega8. no one had it yet except TC but the good thing is it supports Simonk's custom firmware.On the…"
Jeff E commented on Bill Nesbitt's blog post AutoQuad ESC32 v1r5"@Max, thanks for that its the ESC themselves are always getting harder to buy (mostly out of stock). Been following that thread too..but thanks for the link. Just in my opinion if someone got an open source multirotor targeted ESC and ready for easy…"
Jeff E commented on Bill Nesbitt's blog post AutoQuad ESC32 v1r5"Quite interesting to see this ESC. I myself is needing of an ESC that has higher PWM rates tho custom firmware is available its quite hard to get the reliable ones with the ready pin out for programming/flashing. Hope this is open source."
Jeff E commented on jasonshort's blog post Arducopter 2.0.50 preview"Jason here is the CLI test for IMU and the new setup show.
first test was still, 2nd was I was twiching it
IMU test
setup "show"
After this test I noticed something weird, on CLI mode (switch to CLI) the LED on APM is always green as long…"
Jeff E replied to Paul Guggenbuehl's discussion I have a Fyetech.com Y6, I want to put in my IMU/oil-GPS pan system where do I start? in the group ArduCopter User Group"Paul, not to divert you from Arducopter but I think this is what you were waiting for
The sad news is it will cost more than the DJI itself base on other forums. It will be close to MK.
But dont get me wrong Arducopter still…"
Jeff E commented on jasonshort's blog post Arducopter 2.0.50 preview"NO defines, I just loaded directly from GIT nothing was changed. I usually edit the camera.pde and enable the battery event but I didnt do them for this test"
Jeff E commented on jasonshort's blog post Arducopter 2.0.50 preview"there is a big gap where its on the ground, I was going over the flight modes and trying to see which once are showing on my ardustation."
Jeff E commented on jasonshort's blog post Arducopter 2.0.50 preview"Here you go CLI_Setup
I didnt notice anything abnormal but I may have oevrlooked it here is the full video
"
Jeff E commented on jasonshort's blog post Arducopter 2.0.50 preview"ok will watch the change log and wait for the next update to test :)
But I know you must really be busy, specially with your little Lukas"
Profile Information
- About Me:
- RC Hobbist
- Tell us a bit about your UAV interest
- Aerial Photography
Jeff E's Photos
Jeff E's Blog
Finally lifted with camera
Posted on September 6, 2011 at 7:37pm 2 Comments 1 Like
Technically this is 3 frame with camera but the first one was hard to control, weight of GoPro with skeleton cover was too much for weak motors. 2nd one was stock ACM but ended in a crash with v39. Finally this was the only frame/setup can last long enough for me to take a video.
…
ContinueComment Wall (3 comments)
- At 7:20am on July 31, 2011,
DeveloperMichael Oborne said… Jeff, what number are you entgering for declination? just so i can test. all my test show it working correctly.
- At 7:40am on July 31, 2011,
3D RoboticsChris Anderson said… - I think he typed this in the status box by mistake: "I keyed in 0.13 (0deg13') then it will be saved as "-0.2200". I always change it to "0.2167". I know I can set "0.2200""
- At 7:42am on July 31, 2011, Jeff E said…
Yes I did...was trying to undo and try to pm Michael directly..forgot to remove it...s
Social Networking
Top Content
Contests
Season Two of the Trust Time Trial (T3) Contest has now begun. The fourth round is an accuracy round for multicopters, which requires contestants to fly a cube. The deadline is April 14th.A list of all T3 contests is here.
Groups
-
Documentation Editors
51 members
-
ArduRover User Group
184 members
-
ArduCopter User Group
1290 members
-
Swiss Drone Group
11 members
-
Andropilot Users Group
182 members
Advertisement
© 2013 Created by Chris Anderson.
Powered by
