MattMGN
  • Male
  • France
Share
  • Blog Posts
  • Discussions (7)
  • Groups
  • Photos
  • Photo Albums
  • Videos

MattMGN's Friends

  • Mitchell P

MattMGN's Discussions

[PIXHAWK MINI] Telemetry / Serial Port Setup

Started Oct 13 0 Replies

Hello,I am building a light weight foldable quad (550 size) with some options : telemetry, MavLink_FrSkySPort, 3 axis gimbal for the lightweight Runcam Split; based on a 3DR Pixhawk Mini.Thus I am…Continue

 

MattMGN's Page

Latest Activity

MattMGN commented on Chris Anderson's blog post Vision of a full-automated farm drone system
"I am sure that Chris is already aware of farmers needs. For those who doubt, this article will help them understand his approach : https://www.expouav.com/news/latest/drones-will-become-boring-interview-3drs-chris-anderson/ 'Boring' yes…"
Dec 10
MattMGN replied to Christopher Harvey's discussion Disabled veteran with a patent pending drone system needs YOUR help please.
"It depends what kind of informations you want to get : Those sensors can be used directly on Pixhawk through firmware settings https://docs.px4.io/en/getting_started/sensor_selection.html https://pixhawk.org/peripherals/rangefinder If you want to…"
Dec 10
MattMGN replied to Christopher Harvey's discussion Disabled veteran with a patent pending drone system needs YOUR help please.
"The best combo and widely used is Pixhawk with Raspberry Pi as described here http://ardupilot.org/dev/docs/raspberry-pi-via-mavlink.html 'I need to be a coder to work either' --> You will need at least to understand linux…"
Dec 9
MattMGN replied to Christopher Harvey's discussion Disabled veteran with a patent pending drone system needs YOUR help please.
"You are right about Arduino : Both Arduino and Pixhawk/APM are based on microController Although companion boards such as RPi are based on microProcessor"
Dec 9
MattMGN replied to Christopher Harvey's discussion Disabled veteran with a patent pending drone system needs YOUR help please.
"Why you want to install Arduino in addition to Pixhawk ?  Caricaturing : Pixhawk is actually an Arduino, with low level capabilities for flight stabilization, but also supports high level commands through MAVLINK…"
Dec 9
MattMGN replied to Christopher Harvey's discussion Disabled veteran with a patent pending drone system needs YOUR help please.
"Their are plenty of Tx/Rx video system available, it only depends on range (and cost) you are expecting but also on quality and reliability. Some inputs you have to take into account : HD video = high quality, some delay in transmission VS Analogic…"
Dec 9
MattMGN replied to Christopher Harvey's discussion Disabled veteran with a patent pending drone system needs YOUR help please.
"If you want to compare several configurations you can use this site : https://www.ecalc.ch/xcoptercalc.php It will give you some info about flight time regarding motor, battery, propeller... 3520 T-Motors and 5000mAh 6s battery with…"
Dec 8
MattMGN posted a discussion

[PIXHAWK MINI] Telemetry / Serial Port Setup

Hello,I am building a light weight foldable quad (550 size) with some options : telemetry, MavLink_FrSkySPort, 3 axis gimbal for the lightweight Runcam Split; based on a 3DR Pixhawk Mini.Thus I am wondering if it is possible to acces Serial2 port with this board, or something equivalent to Telem2 on its Pixhawk 1 brother.ThanksMatt..MavLink_FrSkySPortSee More
Oct 13
MattMGN commented on Emlid's blog post Major New Raspbian Stretch Release for Navio with ArduCopter-3.5 and ROS Kinetic
"Probably one of the best 'ready to go' FCU/ROS platform available.  Nice job "
Oct 10

Profile Information

Please tell us a bit about your UAV interest
UGV/UAV Engineer
Hometown:
PARIS

Comment Wall

  • No comments yet!

You need to be a member of DIY Drones to add comments!

Join DIY Drones

 
 
 

Groups

Season Two of the Trust Time Trial (T3) Contest 
A list of all T3 contests is here. The current round, the Vertical Horizontal one, is here

© 2017   Created by Chris Anderson.   Powered by

Badges  |  Report an Issue  |  Terms of Service