"http://diydrones.com/forum/topics/relay-or-making-one-pin-5v-on-2-5-ardupilot?xg_source=activity
So I write on blank page (everything commented out) (APM_config.h)?, so I did :
I defined analog 8 to be output (61 according to this) in…"
Mell's Discussions
BATT_VOLT_PIN ardupilot dose not remember changed pin
Started Feb 21 0 Replies 0 Likes
Hello,I added voltage battery monitor to my ardupiltot. I dont use PM (power module) wiring, so I changed the pin 12 and 13 to 1 and 2 in advanced parameters. But after some time the AP forgets the…Continue
Ublox Lea-6h (teoglas) v1.1, messes up Horizont
Started this discussion. Last reply by Greg Fletcher Dec 4, 2012. 1 Reply 0 Likes
Hi,My GPS messes up my pich and roll .. Horizont. Any Ideas abput that issue? Or GPS broken?…Continue
Can not connect to ardupilot
Started this discussion. Last reply by Mell Dec 4, 2012. 3 Replies 0 Likes
HI,I just uptated Mission Planner, and I cant connect to ardupilot.Says:can not establish a connectionvalue of 2500 is not valid for "value". "Value" should be between "minimum" nad…Continue
Cruise throttle vr. airspeed
Started this discussion. Last reply by Mell Nov 26, 2012. 3 Replies 0 Likes
Hi,1. Both: cruise throttle and airspeed can be set, but why?If I set airspeed (TRIM_ARSPD_CM), then throttle cruise percentage(TRIM_THROTTLE) should be dependent conditionally from…Continue
Mell's Page
Latest Activity
Mell posted a discussionBATT_VOLT_PIN ardupilot dose not remember changed pin
Hello,I added voltage battery monitor to my ardupiltot. I dont use PM (power module) wiring, so I changed the pin 12 and 13 to 1 and 2 in advanced parameters. But after some time the AP forgets the new parameters (1 and 2) and changes back to 12 and 13.(also, the comment for the BATT_VOLT_PIN is "...current sensing in pins A0...A13")Any ideas?See More
Mell replied to Andrew Tridgell's discussion ArduPlane 2.69 released"Hi, my first idea is that the plane is going to freeze (real ice on the wings) and...bad..."
Mell replied to Deni Suwardhi's discussion GPS status = 3????"Hi,
It should mean that you have 3Dfix. More than 3 gps satellites locked and ready to go."
Mell replied to Mell's discussion Can not connect to ardupilot"I resolved it, but I quite dont exatly remember how.
I think I installed earlier verion of MP on another computer...and even that did not work.
Maybe I messed something with Ardunio code. Or got an update for MP.
Sorry, It was too…"
Mr N. replied to Mell's discussion Can not connect to ardupilot"Did you get it to work ..I have the same issue but can't seem to resolve it"
Greg Fletcher replied to Mell's discussion Ublox Lea-6h (teoglas) v1.1, messes up Horizont"The jitters in your display will go away if the GPS is outside getting a good signal. Multipath reflections from being inside couses noise on the gps velocity readings which are used in the AHRS."
Mell posted a discussionUblox Lea-6h (teoglas) v1.1, messes up Horizont
Hi,My GPS messes up my pich and roll .. Horizont. Any Ideas abput that issue? Or GPS broken?See More
Mell replied to Bernardo's discussion GPS fix. No 3D fix after update"My GPS problem:
As we can see on picture, we have Satcount (8 sattelites). But seems like MP dose nothing with that info, and displays GPS: NO GPS.
In some mysterious reasons this happens Only with teoglas signed GPS (numbered 1 on…"
Mell replied to Mell's discussion Cruise throttle vr. airspeed"1.2.22 still says "Airspeed in cm/s to aim for when airspeed is enabled in auto mode"
!?"
DeveloperMichael Oborne replied to Mell's discussion Can not connect to ardupilot
"i cant get it to error. can you post a screenshot? where is it failing?"
Leo Hogg replied to Mell's discussion Cruise throttle vr. airspeed"Quite agree, there are gaps in the info. I thought maybe the Trim throttle was for non ASI equipped aircraft. And what does the ‘air speed corresponding to max throttle FBW-B’ do? (standard parameters).
Im still not really sure…"
Mell replied to Søren Kuula's discussion How to restart waypoint flight?"Hi,
I think this is what u look for:
Reset Mission Channel (ArduPlane:RST_MISSION_CH)
RC channel to use to reset the mission to the first waypoint. When this channel goes above 1750 the mission is reset. Set RST_MISSION_CH to 0 to disable."
Mell replied to Mell's discussion Cruise throttle vr. airspeed"Mission Planner 1.2.20 says in Advanced parameter List that TRIM_ARSPD_CM -"Airspeed in cm/s to aim for when airspeed is enabled in auto mode"
I dont want to beleve that it is in centimetes!?"
Profile Information
- About Me:
- Hi
- Tell us a bit about your UAV interest
- Just interested.
- Hometown:
- Tln
Comment Wall
- No comments yet!
Social Networking
Top Content
Contests
Season Two of the Trust Time Trial (T3) Contest has now begun. The fourth round is an accuracy round for multicopters, which requires contestants to fly a cube. The deadline is April 14th.A list of all T3 contests is here.
Groups
-
ArduCopter Italian Group
86 members
-
Documentation Editors
51 members
-
ArduPlane User Group
671 members
-
ArduCopter User Group
1280 members
-
Taiwan ROC ArduPilot Gro…
8 members
Advertisement
© 2013 Created by Chris Anderson.
Powered by
