Olivier
  • Male
  • Saint chamond
  • France
Share Twitter
  • Blog Posts
  • Discussions (19)
  • Groups
  • Photos
  • Photo Albums
  • Videos

Olivier's Friends

  • Marco Robustini
  • fred_fr
 

Olivier's Page

Latest Activity

Olivier replied to Randy's discussion ArduCopter 2.5 released!
"We should organise a multirotor meeting ;-) Olivier"
Apr 24, 2012
Olivier replied to Randy's discussion ArduCopter 2.5 released!
"Hi John,      Have you check your battery just after the crash?I had a similar experience (I was lucky the quad was 1 meter from the ground). When battery start to fall down, controller start to reduce power (if correctly programmed).…"
Apr 24, 2012
Olivier replied to Randy's discussion ArduCopter 2.5 released!
"Hey Chris,        There is some wobbling,  I've flown default parameters that I should adapt a litlle bit. For the fisrt quad I should reduce a litlle bit more StabP, and for the second I think stab_D will halp to…"
Apr 23, 2012
Olivier replied to Randy's discussion ArduCopter 2.5 released!
"Hi Jean Louis,    I'm close to saint chamond. But I'm flying a lot in Feurs or Roanne for F3A training.   Regards.   Olivier"
Apr 23, 2012
Olivier replied to Randy's discussion ArduCopter 2.5 released!
"Hi folks,      Just 2 small vids on test I've conduct on april 17th. All params are standards exept for the first quad where stab_xxx_P is reduced to 4.2.   Second quad with gopro inside.   Good flight…"
Apr 23, 2012
Olivier replied to Randy's discussion ArduCopter 2.5 released!
"Hello John,   Finally I've found my problem with Baro. April 17th was a beautiful day (very sunny), we should pay attention on direct sunlight on Bosch baro. In my case this why I've problem only outside, and why it was working…"
Apr 23, 2012
Olivier replied to Marcus Taylor's discussion instant GPS tracking capabilities
"take a look here : http://code.google.com/p/arducopter/wiki/AC2_FollowMe I've not tested this flight mode.   Regards   Olivier"
Apr 19, 2012
Olivier replied to Randy's discussion ArduCopter 2.5 released!
"John,   About Hole, I've a 30 mm hole drilled under the box, but not on the cover. Wich has maybe enough during winter flight test (not so sunny and warm as tuesday). The reason why i've not made a hole on the top was to avoid air…"
Apr 19, 2012
Olivier replied to Randy's discussion ArduCopter 2.5 released!
"@Marco:      I'm using a 2.4 ghz xbee, cause I've had an issue with 900Mhz module with baro.   Anotherthings to consider here in france 900Mhz is not allowed (used by mobile phone ).  "
Apr 19, 2012
Olivier replied to Randy's discussion ArduCopter 2.5 released!
"Hi John,     Thank you for the info. In my case I'have the problem with or without the cover.  And Barometer value move a lot also on the bench.My propeller and motor have been balanced. An my APM is mount like this: Apm is…"
Apr 19, 2012
Olivier replied to Randy's discussion ArduCopter 2.5 released!
"Chris,       Compass on last flight was working correctly. What I can't understood is why I had problem on only one quad and just for two flight, third flight was ok for the compass but not for the barometer.   For the…"
Apr 18, 2012
Olivier replied to Randy's discussion ArduCopter 2.5 released!
"Hello all, A test report conducts at the field yesterday. Yesterday was a sunny day, so I went to the field to do some test on last firmware version 2.5.6 beta. I went to the field with this 2 quads. First one : Apm 1 2560 Xbee, mag,…"
Apr 18, 2012
Olivier replied to Randy's discussion ArduCopter 2.5 released!
"Hi Palo,   If you want to restore default param, you can do this. Save with MP your actual parameters. Go to CLI Type setup then reset then Y and reboot your APM. Pay attention that this function reset all params, so you'll have to set…"
Mar 22, 2012
Olivier replied to Randy's discussion ArduCopter 2.4 released
"I'm using an APM1 board. I'have also an APM2, but still in delivery box.I can do a test if needed.   Olivier "
Mar 14, 2012
Olivier replied to Randy's discussion ArduCopter 2.4 released
"Hello All,      I've done some pre-flight tests today with latest GIT version. It seems there is something wrong with baro on this version.When I arm the motors alt is set to 0 then rise slowly, (my quad stay on the bench).If I…"
Mar 13, 2012
Olivier replied to James Roney's discussion Barometer Interfere caused by Xbee 900 telelmetry
"I've purchase 2.4 Ghz here: http://www.buildyourowndrone.co.uk/ Nice contact and great services from Martin. About range due to winter weather I've not done long range test. I've only done test between my home and my garage, it works…"
Jan 31, 2012

Profile Information

About Me:
I'm a 42 years old mechanical engineer. I'm practising rc more than 20 years in helicopters, F3a french championship, cars and more ...
Tell us a bit about your UAV interest
2 majors interests, technology and fun
Hometown:
saint chamond

Comment Wall

  • No comments yet!

You need to be a member of DIY Drones to add comments!

Join DIY Drones

 
 
 

Social Networking

Contests

Season Two of the Trust Time Trial (T3) Contest has now begun. The fourth round is an accuracy round for multicopters, which requires contestants to fly a cube. The deadline is April 14th.

A list of all T3 contests is here

Groups

Advertisement

© 2013   Created by Chris Anderson.   Powered by

Badges  |  Report an Issue  |  Terms of Service