"Thanks all for your help, I will try to power up AMP2 board with separate battery and test again."
OnGaKu's Discussions
(Help) AMP2 problem
Started this discussion. Last reply by OnGaKu Jul 19, 2012. 12 Replies 0 Likes
Hi everyone, I have some problem with my AMP2:1. After I setup my new AMP2 step by step with instruction in code.google.com it running. But I found if I move any Rx stick quicker the AMP2 auto dis…Continue
OnGaKu's Page
Latest Activity
Jeff Smith replied to OnGaKu's discussion (Help) AMP2 problem"I have not found a solid answer to powering with the USB "in-flight", I started a thread with the question days ago, but no answer.
I have been testing my board with USB plugged in and power from my heli going to the input side of the APM…"
OnGaKu replied to OnGaKu's discussion (Help) AMP2 problem"Can I connect battery when USB connected to AMP2 board for watching AMP planer while the issue happens? I never do that before, if it ok I think I can watching what appear in the AMP planer whilt the issue happens."
OnGaKu replied to OnGaKu's discussion (Help) AMP2 problem"My battery is full charged and when I test 2 batteries parallel the same problem. My AMP2 board power by include 5v board, not use 5v power from ESC. Few week ago when I connect all motors spin normal it's ok but when I connect reverse 3 motors…"
Derek Ernewein replied to OnGaKu's discussion (Help) AMP2 problem"Are you saying that the APM disarms its self but the motors still spin? "auto dis arm, motors still rotate".
Can you post a video of the issue so it is easier for everyone to understand what is happening?
Have you tried watching the Tx…"
Jeff Smith replied to OnGaKu's discussion (Help) AMP2 problem"It sounds to me that you are having a power issue, when the motors load up the power to the APM is dropping out.
Is the battery fully charged?
Do you have a volt meter to watch the voltage to the APM when the motors load up?
I am no APM expert,…"
OnGaKu replied to OnGaKu's discussion (Help) AMP2 problem"Nobody can tell me how to solve my AMP2 problem ? I still cannot flight with it :((."
Derek Ernewein replied to OnGaKu's discussion (Help) AMP2 problem"Stabilize mode will keep it level. I find this to be the best mode to start in.
It is also good to use to recover from a user-error."
OnGaKu replied to OnGaKu's discussion (Help) AMP2 problem"Thanks you, so which normal flight mode should be? Stabilize or Acro mode?
"
OnGaKu replied to OnGaKu's discussion (Help) AMP2 problem"After setup I didn't change any thing in Radio. My radio is DX6i. Is this problem because PID setting?
"
ModeratorJohn Church replied to OnGaKu's discussion (Help) AMP2 problem
"No manual mode for multicopters. APM control is required to mix the rc inputs for multicopter control."
Ismail Akcoral replied to OnGaKu's discussion (Help) AMP2 problem"Pls check after initial setup if you changed on your radio travel adjust or endpoint settins."
OnGaKu posted a discussion(Help) AMP2 problem
Hi everyone, I have some problem with my AMP2:1. After I setup my new AMP2 step by step with instruction in code.google.com it running. But I found if I move any Rx stick quicker the AMP2 auto dis arm, motors still rotate, AMP2 arm led still on but cannot re arm or dis arm or do anything. I swich it off and on, it back to normal, arm and put throttle stick about 30%-40% (without propeller for safe) and hold my hexa by hand, move it forward, backward, left, right...if I move it very slowly, it…See More
Profile Information
- Tell us a bit about your UAV interest
- I like videography
Comment Wall
- No comments yet!
Social Networking
Top Content
Contests
Season Two of the Trust Time Trial (T3) Contest has now begun. The fourth round is an accuracy round for multicopters, which requires contestants to fly a cube. The deadline is April 14th.A list of all T3 contests is here.
Groups
-
Andropilot Users Group
203 members
-
Spanish arducopter Users
88 members
-
Moderators
24 members
-
ArduPlane User Group
720 members
-
ArduCopter User Group
1355 members
Advertisement
© 2013 Created by Chris Anderson.
Powered by
