"
no, we havent tried it yet. Project is slowly moving forward, mainly focussing on sail-powered. For electric powered, i would look at the ardurover-coder."
Rob's Discussions
CLI connection YES - MAVlink connection NO
Started this discussion. Last reply by Michael Pursifull Sep 29, 2011. 39 Replies 0 Likes
Does any one know a solution to the problem shown in the attached picture.? Using the latest version Arducopter 2.0.36 and the APM Planner 1.0.36.Reuploaded the code several times. The board seems to…Continue
Rob's Page
Latest Activity
Rob commented on Jean-Louis Naudin's blog post APMRover 2, a fun UGV project for full autonomous recon missions..."i just downloaded the 2.20firmware and set apm2 and lite disabled and uploaded the firmware. that gives me the modes: auto, auto, stabilize, stabilize, manual, manual. Switching from auto to manual goes good, switching back to auto re-initializes…"
Rob commented on Jean-Louis Naudin's blog post APMRover 2, a fun UGV project for full autonomous recon missions..."found the solution (atleast for my problems) i changed the saved modes in apmplanner and now the board doesnt re-initialize."
Rob commented on Jean-Louis Naudin's blog post APMRover 2, a fun UGV project for full autonomous recon missions..."I can change from RTL to MANUAL, but changing back to RTL resets the APM2"
Rob commented on Jean-Louis Naudin's blog post APMRover 2, a fun UGV project for full autonomous recon missions..."Mode channel is connected to In8. Just tested firmware 2.16 and same problem (changing mode goes correct, changing the mode back re-initialises the board). so i am starting to doubt my settings in my Tx, which is the turnigy 9x. More testing is…"
Rob commented on Jean-Louis Naudin's blog post APMRover 2, a fun UGV project for full autonomous recon missions..."With firmware 2.20a and LITE DISABLED & CONFIG_APM_HARDWARE APM_HARDWARE_APM2 set, i also got the problem that when changing modes that my APM2 resets. Has anyone found a fix yet?"
Rob commented on Jean-Louis Naudin's blog post APMRover 2, a fun UGV project for full autonomous recon missions..."Tried 2.20 today in my Himoto MT10 Brushless with an APM2 today. Just indoor testing, we got rain.
After powering up control was good through my Turnigy 9x. But after connecting with APMplanner using the 3DR 433mhz radios, i couldnt control the car…"
Rob commented on lot's blog post Dutch ministry of defense forbids take aerial pictures without permission"yes, it is an old law, completely obsolete now. But the Netherlands is knows only 1 thing, and that is to make things illegal. This law was made to protect military secrets, but all the army bases are visible on Bing-maps. If you do soem creative…"
Rob commented on Jean-Louis Naudin's blog post APMRover 2, a fun UGV project for full autonomous recon missions..."Hi, a lot has changed since the start of the thread. Could the first post be edited so it is up to date and also includes a shop where to get the Sharp sensor? I've been following it from the start and got my own car (had to sell my apm2 to…"
Rob commented on Jean-Louis Naudin's blog post APMRover 2, a fun UGV project for full autonomous recon missions..."I got the same problem."
Rob commented on Sina Kazemi's blog post The Trimaran(Anna)"It was a nice day to see it get in the water. Really hoped it wouldn't sink :) and it didnt. It performed above my goals. The design needs a couple of modifications and then it is easily build in one afternoon. Due to the parts and sizes used,…"
Rob commented on Joseph's blog post 40mm retractable camera turret"I got a 3D-printer here, so could help out. and i am very handy with Sketchup. I like the block cameras and i would vote to have atleast the gopro be usable, as that is one of the most popular camera used."
Rob commented on Chris Anderson's blog post APM-powered hexacopter project on Kickstarter"isnt that the same frame as on kickstarter?"
Rob commented on Chris Anderson's blog post APM-powered hexacopter project on Kickstarter"then why is this one so expensive too?"
Rob commented on Martint BuildYourOwnDrone.co.uk's blog post ArduPilot Mega & Arducopter 2.4 GHz Telemetry Kit for UK & EU"for those people you are preaching to the choir. They wouldnt invest in those if they didnt kow and want to abide by the rules."
Profile Information
- About Me:
- a guy
- Tell us a bit about your UAV interest
- moving 3d platform
Rob's Photos
Rob's Blog
AttoPilot Voltage Kit
Posted on September 29, 2011 at 5:08am 2 Comments 4 Likes
APM Mission Planner is adding more support for the AttoPilot Voltage Sensor. Thus the Open Hardware Store has introduced a voltage sensor kit that is ready to be used and you just need to plug it in and configure Ardupilot. It comes with XT60-connectors and a 15cm long servo cable to connect to the…
ContinueComment Wall
- No comments yet!
Social Networking
Top Content
Contests
Season Two of the Trust Time Trial (T3) Contest has now begun. The fourth round is an accuracy round for multicopters, which requires contestants to fly a cube. The deadline is April 14th.A list of all T3 contests is here.
Groups
-
Moderators
24 members
-
ArduCopter User Group
1299 members
-
Melbourne
48 members
-
Documentation Editors
51 members
-
UK Ardupilot Group
111 members
Advertisement
© 2013 Created by Chris Anderson.
Powered by
