"We were running 3.0.0rc5. Team Special Delivery were running 2.9.1. We increased our speed slightly on each run, but our vehicle maxes out at about 16 or 17 m/s."
3D Robotics
-
Sam Kelly
- Male
- San Diego, CA
- United States
- Blog Posts (8)
- Discussions (27)
- Groups (1)
- Photos
- Photo Albums
- Videos
Sam Kelly's Page
Latest Activity
3D RoboticsSam Kelly commented on Joshua Ott's blog post AVC media
"It's weird seeing myself without my beard."
3D RoboticsSam Kelly commented on Joshua Ott's blog post Thirty Days (#23): New Product Preview
"Some kind of overly complicated pez dispenser."
3D RoboticsSam Kelly commented on Joshua Ott's blog post Thirty Days (#23): New Product Preview
"I think it that's a Raspberry Pi."
Алексей Ойнац commented on Sam Kelly's blog post Remzibi OSD now in stock at the DIY Drones store"Hi guys!
I have purchased this board several months ago and I hoped to use it with CRIUS AIOP board + MegapirateNG.
But it seems that 3DR Remzibi board can't understand MAVlink protocol at all.
I've tried different firmwares (ARDU1.73,…"
3D RoboticsSam Kelly commented on John C.'s blog post Photosynthesis Assessments
"Take me down to the parallax city"
Sebastian Gralla commented on Sam Kelly's blog post ArduPilotMega + Spektrum satellite Rx -- NOW AVAILABLE"still no update on this? i have one of these adaptors, will it work with APM2.5?
I assume if it would they would still be available..."
Euan Ramsay commented on Sam Kelly's blog post Minimalist ArduCopter 3DR build"The APM probably has more computing power than that old PC...:-)
Kudo though. Nice build. Tidy wiring too. Where is the Spektrum adapter btw?"
Sérgio Domingos commented on Sam Kelly's blog post Remzibi OSD now in stock at the DIY Drones store"Hi Legot, i've not used this OSD for a while, but i remember that too much voltage was causing the issue, try powering the OSD with a 2S lipo i believe that should do the trick"
Legot commented on Sam Kelly's blog post Remzibi OSD now in stock at the DIY Drones store"Sergio, would you mind telling me the solution to the random numbers scrolling across the screen issue? I've been having the same problem, but I haven't found a solution anywhere."
3D RoboticsSam Kelly commented on John C.'s blog post 25% Discount at Our New Store
"Michael, telemetry kits are still available at our regular site: http://store.diydrones.com/SearchResults.asp?Search=telemetry+kit&Search.x=0&Search.y=0
http://store.3drobotics.com does not yet have our full catalog."
Corentin Chéron commented on Sam Kelly's blog post New 3D Robotics product: u-blox LEA-6H GPS"By the way, it seems there is a wrong labeling of TX and RX pads on the silk screen, and I have confirmed it on the brd file 3DR-GPS-LEA6-JST-v11-RELEASE.brd.
If the reference used is the GPS, then the RX pad is in fact connected to the TX GPS…"
Corentin Chéron commented on Sam Kelly's blog post New 3D Robotics product: u-blox LEA-6H GPS"Default configuration when shipped says that only UBX protocol is output to UART1,
Go to CFG ->PRT and enable 0+1 - UBX+NMEA for protocol Out for UART1.
"
3D RoboticsSam Kelly replied to Daniel Melia's discussion No AHRS Data in Mission Planner
"Hi Daniel. Try opening the Mission Planner terminal and seeing if the logs are being erased at boot-up. If that is happening, you need to wait for that to finish, then your board will operate normally."
3D RoboticsSam Kelly commented on Nick Butt's blog post Mind control system for Drones / helicopters.
"I tried one for a few minutes. Couldn't get it to fly :("
Profile Information
- About Me:
- I do things at 3D Robotics.
- Tell us a bit about your UAV interest
- The most significant bit or the least significant bit? ;)
Sam Kelly's Blog
New 3D Robotics product: u-blox LEA-6H GPS
Posted on July 3, 2012 at 3:30pm 85 Comments 8 Likes
Hi everyone! I'm very happy to announce our new u-blox based GPS board. The development teams and 3D Robotics have been working on this GPS unit for some time, and we have seen very good results on ArduPlane, ArduCopter and ArduRover. The Sparkfun AVC and the Quadcopter Rodeo were excellent opportunities to observe this GPS…
New product! The 3DR Radio Telemetry System
Posted on April 6, 2012 at 1:00pm 128 Comments 21 Likes
Hi everyone, I'm very happy to announce something that 3D Robotics has been working on since late last year in cooperation with a few very talented developers. Today we are announcing the 3DR Radio telemetry system, an open-source alternative to XBee telemetry set-ups, with superior…
ContinueRemzibi OSD now in stock at the DIY Drones store
Posted on December 23, 2011 at 3:19pm 47 Comments 6 Likes
Hi everybody! I'm very happy to announce that the Remzibi OSD DIY Drones variant is now in stock in the DIY Drones store!
Our version is fully compatible with the original…
ContinueComing soon: MinimOSD!
Posted on November 10, 2011 at 6:00pm 63 Comments 13 Likes
Hi guys! I'm giving you a preview of an upcoming product from the DIY Drones store, the MinimOSD, a minimal Arduino-based on-screen display board. It's tailored for use with ArduPilot Mega and the MAVlink protocol, and designed to be as compact as possible.
It's main components are an…
ContinueComment Wall
- No comments yet!
Social Networking
Top Content
Contests
Season Two of the Trust Time Trial (T3) Contest has now begun. The fourth round is an accuracy round for multicopters, which requires contestants to fly a cube. The deadline is April 14th.A list of all T3 contests is here.
Groups
-
DIYDrones News Team
5 members
-
ArduCopter User Group
1356 members
-
Melbourne
54 members
-
Andropilot Users Group
203 members
-
Spanish arducopter Users
88 members
Advertisement
© 2013 Created by Chris Anderson.
Powered by
