"still no update on this? i have one of these adaptors, will it work with APM2.5?
I assume if it would they would still be available..."
3D Robotics
-
Sam Kelly
- Male
- San Diego, CA
- United States
- Blog Posts (8)
- Discussions (27)
- Groups (1)
- Photos
- Photo Albums
- Videos
Sam Kelly's Page
Latest Activity
Sebastian Gralla commented on Sam Kelly's blog post ArduPilotMega + Spektrum satellite Rx -- NOW AVAILABLE
Euan Ramsay commented on Sam Kelly's blog post Minimalist ArduCopter 3DR build"The APM probably has more computing power than that old PC...:-)
Kudo though. Nice build. Tidy wiring too. Where is the Spektrum adapter btw?"
Sérgio Domingos commented on Sam Kelly's blog post Remzibi OSD now in stock at the DIY Drones store"Hi Legot, i've not used this OSD for a while, but i remember that too much voltage was causing the issue, try powering the OSD with a 2S lipo i believe that should do the trick"
Legot commented on Sam Kelly's blog post Remzibi OSD now in stock at the DIY Drones store"Sergio, would you mind telling me the solution to the random numbers scrolling across the screen issue? I've been having the same problem, but I haven't found a solution anywhere."
3D RoboticsSam Kelly commented on John C.'s blog post 25% Discount at Our New Store
"Michael, telemetry kits are still available at our regular site: http://store.diydrones.com/SearchResults.asp?Search=telemetry+kit&Search.x=0&Search.y=0
http://store.3drobotics.com does not yet have our full catalog."
Corentin Chéron commented on Sam Kelly's blog post New 3D Robotics product: u-blox LEA-6H GPS"By the way, it seems there is a wrong labeling of TX and RX pads on the silk screen, and I have confirmed it on the brd file 3DR-GPS-LEA6-JST-v11-RELEASE.brd.
If the reference used is the GPS, then the RX pad is in fact connected to the TX GPS…"
Corentin Chéron commented on Sam Kelly's blog post New 3D Robotics product: u-blox LEA-6H GPS"Default configuration when shipped says that only UBX protocol is output to UART1,
Go to CFG ->PRT and enable 0+1 - UBX+NMEA for protocol Out for UART1.
"
3D RoboticsSam Kelly replied to Daniel Melia's discussion No AHRS Data in Mission Planner
"Hi Daniel. Try opening the Mission Planner terminal and seeing if the logs are being erased at boot-up. If that is happening, you need to wait for that to finish, then your board will operate normally."
Drone Savant commented on Sam Kelly's blog post Remzibi OSD now in stock at the DIY Drones store""I too am disappointed. I had to buy my own 3DR Remzibi OSD after it came out. Not once was I contacted during development. Once I got mine, I couldn't get it to work with my software. So far, I've been able to get it to program…"
Drone Savant commented on Sam Kelly's blog post Remzibi OSD now in stock at the DIY Drones store"Per the TAPR license that Remzibi uses you must publish the modifications that were made. I don't see them up at:https://store.diydrones.com/Remzibi_OSD_3DR_p/br-remzibiosd.htmPlease advise. "* You may distribute unmodified…"
3D RoboticsSam Kelly commented on Nick Butt's blog post Mind control system for Drones / helicopters.
"I tried one for a few minutes. Couldn't get it to fly :("
3D RoboticsSam Kelly commented on Jake Bayless's blog post DIYDrones in the press - The California Report (KQED audio)
"Somehow "a former editor" sounds less impressive than "the former editor"."
3D RoboticsSam Kelly commented on Chris Anderson's blog post Stephen Hawking joins foundation to defend humanity against autonomous robots
"Well, the fact that we haven't been enslaved by a time-traveling AI from the future is proof enough for me that their project is working (or will work?)."
3D RoboticsChris Anderson commented on Sam Kelly's blog post New product! The 3DR Radio Telemetry System
"Any 900Mhz antenna with a RP-SMA connector will work. "
StamusContra commented on Sam Kelly's blog post New product! The 3DR Radio Telemetry System"Hey guys, I lost one of the antennas to my 915mhz telemetry kit. Does anyone know if I need to purchase the antenna from 3dr or could pick up another antenna locally (radioshack or computer hardware store etc)?"
Profile Information
- About Me:
- I do things at 3D Robotics.
- Tell us a bit about your UAV interest
- The most significant bit or the least significant bit? ;)
Sam Kelly's Blog
New 3D Robotics product: u-blox LEA-6H GPS
Posted on July 3, 2012 at 3:30pm 85 Comments 8 Likes
Hi everyone! I'm very happy to announce our new u-blox based GPS board. The development teams and 3D Robotics have been working on this GPS unit for some time, and we have seen very good results on ArduPlane, ArduCopter and ArduRover. The Sparkfun AVC and the Quadcopter Rodeo were excellent opportunities to observe this GPS…
New product! The 3DR Radio Telemetry System
Posted on April 6, 2012 at 1:00pm 128 Comments 21 Likes
Hi everyone, I'm very happy to announce something that 3D Robotics has been working on since late last year in cooperation with a few very talented developers. Today we are announcing the 3DR Radio telemetry system, an open-source alternative to XBee telemetry set-ups, with superior…
ContinueRemzibi OSD now in stock at the DIY Drones store
Posted on December 23, 2011 at 3:19pm 48 Comments 6 Likes
Hi everybody! I'm very happy to announce that the Remzibi OSD DIY Drones variant is now in stock in the DIY Drones store!
Our version is fully compatible with the original…
ContinueComing soon: MinimOSD!
Posted on November 10, 2011 at 6:00pm 63 Comments 13 Likes
Hi guys! I'm giving you a preview of an upcoming product from the DIY Drones store, the MinimOSD, a minimal Arduino-based on-screen display board. It's tailored for use with ArduPilot Mega and the MAVlink protocol, and designed to be as compact as possible.
It's main components are an…
ContinueComment Wall
- No comments yet!
Social Networking
Top Content
Contests
Season Two of the Trust Time Trial (T3) Contest has now begun. The fourth round is an accuracy round for multicopters, which requires contestants to fly a cube. The deadline is April 14th.A list of all T3 contests is here.
Groups
-
ArduCopter User Group
1286 members
-
ArduCopter Italian Group
87 members
-
techpod users
39 members
-
Moderators
24 members
-
Turkish Ardu Group
5 members
Advertisement
© 2013 Created by Chris Anderson.
Powered by
