"Hi. Besides the suspect being a 'bad' radio (i.e. defective radio). Try this:
1. Connect good radio to Mission planner and upload its parameters.
2. Rmove good radio and connect 'bad' radio.
3. Download the parameters from the…"
Serg Abad's Discussions
Weird 3 Axis Camera Gimbal Operation
Started this discussion. Last reply by Serg Abad Dec 7, 2012. 3 Replies 0 Likes
Hi Guys,I seem to have encountered some weird camera gimbal operation with APM 2.5 and MP 1.2.22. I have used the APM 2.0 before with camera stab fine with pitch and yaw. This is the first time I…Continue
Problem with Mission Planner 1.2.1 and Recent Arducopter 2.7 hex Update
Started this discussion. Last reply by Serg Abad Aug 1, 2012. 5 Replies 0 Likes
Hi guys. I just encountered a problem with the most recent update of MP 1.2.1 Mav 1.0 and AC 2.7 update. While trying to connect to establish a data link (USB) to APM2 board it either stops midway…Continue
3DR 433 Mhz Radios not working
Started this discussion. Last reply by Serg Abad Jan 27. 26 Replies 0 Likes
Hi,I have almost the same problem as droter and kbcopter in this forum. My observations:One of the 3DR radios (433 mhz vers.) seems to be ok but I am not sure. It flashes the green LED, but the red…Continue
Serg Abad's Page
Latest Activity
vitaly replied to Serg Abad's discussion 3DR 433 Mhz Radios not working"same here the funny part was I"
mP1 replied to Serg Abad's discussion 3DR 433 Mhz Radios not working"Tried connecting the "air" radio using the USB, but i cant load settings or do any ATI commands. The config util always complains with "Fail to enter command mode". Strangely the radio always has a green solid LED even when the…"
mP1 replied to Serg Abad's discussion 3DR 433 Mhz Radios not working"Hi Serg, i am experiencing the similar problems with my new system. The ground stations radio always blinks its green led, while the hexcopter(remote) radio is solid green with a few red flashes every second or so. Ive noticed that the remote knows…"
Serg Abad replied to Serg Abad's discussion Weird 3 Axis Camera Gimbal Operation"Since no one has replied to this thread, it looks like nobody has really tried using the pan servo output of APM. :( "
Serg Abad replied to Serg Abad's discussion Weird 3 Axis Camera Gimbal Operation"An additional observation is that the pan stab servo is not responding at all to any motion of the APM. There seems to be no servo signal to the motor since I do not encounter resistance when I try to rotate it slightly. And the pan servo works…"
Serg Abad replied to Serg Abad's discussion Weird 3 Axis Camera Gimbal Operation"Btw, I am using the later ArduPlane Firmware 2.67"
Serg Abad posted a discussionWeird 3 Axis Camera Gimbal Operation
Hi Guys,I seem to have encountered some weird camera gimbal operation with APM 2.5 and MP 1.2.22. I have used the APM 2.0 before with camera stab fine with pitch and yaw. This is the first time I have used all three camera axes - pitch, roll and yaw on APM 2.5. I have configured the pitch, roll and yaw for Aux Ch 11,10, and 9 respectively. All 3 RC input channels for these ACs have been disabled. If I disable pan stab, the pitch stab and roll stab servos work correctly. However, if I enable pan…See More
Serg Abad replied to Don Fiedler's discussion Unexpected motor glitches (speed up) with Tri Hex and Octo APM 2 & APM 2.5 using 2.73"Hi,
We just fixed our own motor glitches and twitches problem after some time. The culprit was the multi-connector cable between receiver and APM board. They were probably a bit worn and if there is some vibration, they loose contact.…"
Serg Abad replied to marcelo's discussion Apm2 xquad glitches/flickering Thottle - DEFAULT PIDS"I am experiencing the same problem after an update to 2.7.1 which was not present in 2.7.0. I hope this gets cleared soon. Thanks to all."
Serg Abad replied to Serg Abad's discussion Problem with Mission Planner 1.2.1 and Recent Arducopter 2.7 hex Update"Found out problems and fixed now.
Newest upload of MP 1.2.1 does not contain the proper firmware of Arducopter 2.7.1 (since it is still a release candidate?). But it does now.
Also, was able to fix serial data dropping problem by resetting the…"
Serg Abad replied to Serg Abad's discussion Problem with Mission Planner 1.2.1 and Recent Arducopter 2.7 hex Update"Hi Jason,
This is the content of the arduino serial window port monitor. Hope this helps in the diagnosis.
"
Serg Abad replied to Serg Abad's discussion Problem with Mission Planner 1.2.1 and Recent Arducopter 2.7 hex Update"Hi Jason,
It looks like a serial rate (too high or buffer flush/overrun) problem with the new flashing. I checked the port parameters (port no. and baud rate) on my machine and they are correct. The MP 1.2.1 either connects momentarily to get an…"
Serg Abad replied to Serg Abad's discussion Problem with Mission Planner 1.2.1 and Recent Arducopter 2.7 hex Update"Hi Jason,
Apologies for the delayed response, as we are in different time zones. Unfortunately, I haven't gone into the gritty side with Arduino yet. But, will try. I do understand though that it is a communication problem and…"
Developerjasonshort replied to Serg Abad's discussion Problem with Mission Planner 1.2.1 and Recent Arducopter 2.7 hex Update
"Use Arduino to connect via a serial port. Let me know what the serial window prints out.
Jason
"
Serg Abad posted a discussionProblem with Mission Planner 1.2.1 and Recent Arducopter 2.7 hex Update
Hi guys. I just encountered a problem with the most recent update of MP 1.2.1 Mav 1.0 and AC 2.7 update. While trying to connect to establish a data link (USB) to APM2 board it either stops midway (or somewhere near the end) during connection or goes through but drops the connection immediately. Also, the 3DR radios no longer connect to each other (steady green but no more blinking red lights on both radios!). All I did was to update the system when MP told me that there are new updates. What…See More
Profile Information
- About Me:
- TinkerMan
- Tell us a bit about your UAV interest
- Possibilities!
Comment Wall
- No comments yet!
Social Networking
Top Content
Contests
Season Two of the Trust Time Trial (T3) Contest has now begun. The fourth round is an accuracy round for multicopters, which requires contestants to fly a cube. The deadline is April 14th.A list of all T3 contests is here.
Groups
-
Documentation Editors
51 members
-
ArduCopter Italian Group
87 members
-
Moderators
24 members
-
ArduPlane User Group
683 members
-
ArduRover User Group
184 members
Advertisement
© 2013 Created by Chris Anderson.
Powered by
