"I just test it on evening and it still loiter tuning.
"
Balloon's Groups
-
Learning to program the …
313 members
-
ArduCopter Evolution Team
140 members
-
ArduCopter User Group
1289 members
Balloon's Discussions
APM2.5 Barometer on APM Problem
Started this discussion. Last reply by Balloon Mar 13. 7 Replies 0 Likes
All, I have a problem about Altitude when connect to APM Planner is error value and lag update. And, When i change to ALT Hold is yo-yo (jiggle up-down) But, It's set altitude at 1-2 meter…Continue
I can't connect APM Planner between Xbee telemetry and APM2.5
Started Sep 27, 2012 0 Replies 0 Likes
I don't know have a problem about connect cable from xbee to APM2.5. Because, I can't connect by APM Planner. What i would do connect or solder or jump connector on board.Help me pls...Continue
Test Loiter By arducopter 2.0.46 update
Started this discussion. Last reply by Tomas Soedergren Oct 25, 2011. 28 Replies 0 Likes
About midday. I just test my arducopter code 2.0.46 update in Loiter mode. It have best. But, Something move circle (CCW) from center about 3-5 m. And I don't all tuning (default PI). Bad weather…Continue
Balloon's Page
Latest Activity
Balloon replied to Randy's discussion ArduCopter 2.9 / 2.9.1 released"I just use Rubber anti-vibration and change prop from 10x38 to 10x45 is can alt_hold no have problem again.
"
Balloon replied to Balloon's discussion APM2.5 Barometer on APM Problem"Yes, It have foam in APM case. "
3D RoboticsChris Anderson replied to Balloon's discussion APM2.5 Barometer on APM Problem
"And your board is in the enclosure, with the foam inside?"
Balloon replied to Balloon's discussion APM2.5 Barometer on APM Problem"Chris,
I not used sonar sensor. Barometer only and when it take off by stabilize mode it show altitude is incorrect (real altitude is 1 m. in APM Planner is show 5 -10 or minor value) and when change to 2.8.1 is no have problem it. I…"
Balloon replied to Balloon's discussion APM2.5 Barometer on APM Problem"It have problem on Firmware 2.9 - 2.9.1 only. but, when i had used 2.8.1 is no problem."
3D RoboticsChris Anderson replied to Balloon's discussion APM2.5 Barometer on APM Problem
"Are you using a sonar sensor? If so, disable it in the Mission Planner. "
Mike Mac replied to Balloon's discussion APM2.5 Barometer on APM Problem"What firmware do you have loaded?"
Balloon replied to Randy's discussion ArduCopter 2.9 / 2.9.1 released"But, I have down to 2.8.1 is Altitude value normal."
Balloon posted a discussionBarometer on APM Problem
All, I have a problem about Altitude when connect to APM Planner is error value and lag update. And, When i change to ALT Hold is yo-yo (jiggle up-down) But, It's set altitude at 1-2 meter only. I don't know it than. Please help me. P.S It problem is new board from 3DRobotics. Thank for helpSee More
Balloon replied to Randy's discussion ArduCopter 2.9 / 2.9.1 released"Randy and all
I have altitude hold is problem in new board. i just order new and flight test APM 2.5 is ok, But when I changed to altitude hold is had jiggle on the air and I seen on APM Planner is had Altitude lag update (at 3…"
Balloon replied to Randy's discussion ArduCopter 2.9 / 2.9.1 released"Thank, Marco. But, when it had headwind to it. It's still little move out and tilt to back position.(It feel DJI same)
Today, I test loiter's altitude at 200 meters it very nice.
"
Balloon replied to Randy's discussion ArduCopter 2.9 / 2.9.1 released"On evening, Loiter test low altitude.
"
Balloon replied to Randy's discussion ArduCopter 2.9 / 2.9.1 released"I'm not use all anti-vibration. But, I do balance all propellers same.
"
Profile Information
- About Me:
- I like Quadrotor....
- Tell us a bit about your UAV interest
- Quadrotor UAV Project
- Hometown:
- Thailand
Balloon's Photos
Balloon's Blog
Test Sonar wiring Shield Perfect No Noise
Posted on September 4, 2011 at 3:30am 6 Comments 2 Likes
Today I'm test sonar my Arducopter in ALT Hold Mode. I use USB HUD cable (Have Shield) connect to Pitot port IMU and receive signal from AN (pin 3) the Sonar. It perfect not noise in test.
Now, I use code ArduCopter2.0.39b
Wiring shield to ground at Sonar.
…
ContinueComment Wall
- No comments yet!
Social Networking
Top Content
Contests
Season Two of the Trust Time Trial (T3) Contest has now begun. The fourth round is an accuracy round for multicopters, which requires contestants to fly a cube. The deadline is April 14th.A list of all T3 contests is here.
Groups
-
ArduCopter User Group
1289 members
-
ArduCopter Evolution Team
140 members
-
Learning to program the …
313 members
-
ArduIMU Gimbal Controller
44 members
-
Arducopter Tech Support
5 members
Advertisement
© 2013 Created by Chris Anderson.
Powered by
