Trey Hagg
  • Male
  • Lancaster, KY
  • United States
Share
  • Blog Posts
  • Discussions (20)
  • Groups
  • Photos
  • Photo Albums
  • Videos

Trey Hagg's Discussions

Step 10 in Mission Planner??

Started this discussion. Last reply by Trey Hagg May 22. 2 Replies

Hello all,I finally learned that my problem with the binding issue was that I wasn't removing the bind plug, and that was therefore putting the receiver in bind mode every time after I restarted the…Continue

What receivers are compatible with the Turnigy Dsss 2.4 GHz transmitter module?

Started May 4 0 Replies

So I posted a few discussions covering the RC issues I've been having. Thinking about it, I started wondering if my module and receiver were even compatible.I have a Dsss transmitter module with a…Continue

Transmitter and receiver not binding

Started Apr 17 0 Replies

So, I have a 9xr Pro with a Dsss transmitter module and I'm trying to pair it with a Turnigy 9x version 2 8ch receiver, but they just don't seem to want to bind properly. When I plug the battery into…Continue

Holding an RX/TX bind

Started Mar 22 0 Replies

Hi, I'm building a quadcopter, and I need some assistance on a receiver-related issue.Before I explain my problem, I should probably list my hardware.Receiver: Turnigy 2.4 GHz 8chTransmitter: Turnigy…Continue

 

Trey Hagg's Page

Latest Activity

Trey Hagg replied to Trey Hagg's discussion Step 10 in Mission Planner??
"So it seems as soon as I posted that reply, I figured out how to fix the yaw issue and now I have a new issue: The safety prearm checks. Here's what it says PreArm: Accelerometers calibrated requires rebootPreArm: GPS HDOP 5.2 (needs…"
May 22
Trey Hagg replied to Trey Hagg's discussion Step 10 in Mission Planner??
"Update: I got past step 10, it turns out my RC wasn't calibrated. The firmware was uploaded properly, and the failsafe was also set up without issue. This isn't necessarily an issue, but more of a space saving question. Is the External GPS…"
May 22
Trey Hagg posted a discussion

Step 10 in Mission Planner??

Hello all,I finally learned that my problem with the binding issue was that I wasn't removing the bind plug, and that was therefore putting the receiver in bind mode every time after I restarted the quad, so that's out of the way. Now that the Rx/Tx are communicating properly, I have learned that my problem now is with the Rx/FC connections, or lack thereof. I'm using the Turnigy 2.4GHz 8ch PPM receiver and a Pixhawk, and connecting them with the Hobbypower V2.0 PPM encoder.…See More
May 19
Trey Hagg posted a discussion

What receivers are compatible with the Turnigy Dsss 2.4 GHz transmitter module?

So I posted a few discussions covering the RC issues I've been having. Thinking about it, I started wondering if my module and receiver were even compatible.I have a Dsss transmitter module with a Turnigy 9XR Pro, trying to connect it with my receiver, a Turnigy 9X 2.4 GHz 9ch receiver. For the problems with my RC equipment, see my other discussions.My question is whether my receiver is compatible with that particular module. If not, can anybody point me towards a receiver that is? The…See More
May 4
Trey Hagg replied to Skhumbuzo Dube's discussion Hoverboard
"I just wanted to point out that the Lexus Hoverboard was a joke video. They buried a conductive metal track underneath the concrete so it followed a certain path. Great video, though!"
May 3
Trey Hagg replied to Skhumbuzo Dube's discussion Hoverboard
"I think he means making a hoverboard as in an actual hoverboard. Where would he put the stickers without a hoverboard?"
May 1
Trey Hagg replied to Trey Hagg's discussion Powering a receiver with the Pixhawk
"Hi, Sorry I didn't get back sooner. I used a Nimh battery on the receiver and it turns out it's fried because of the charger I used to be using on the battery I had. I got a new battery and charger, so that isn't a problem anymore. I…"
May 1
Trey Hagg posted a discussion

Transmitter and receiver not binding

So, I have a 9xr Pro with a Dsss transmitter module and I'm trying to pair it with a Turnigy 9x version 2 8ch receiver, but they just don't seem to want to bind properly. When I plug the battery into the receiver, the red flashing light comes on and I grab my transmitter and hold the bind button down while turning it on (like you're supposed to do). The light goes solid and I reset everything like all the videos show. But when I plug all the channels back into the receiver and turn on the whole…See More
Apr 17
Trey Hagg replied to neil sam's discussion Breaking solar cells into pieces
"The way I look at it is, if you don't actually break any of the cells, you can separate them to the desired separation and connect them with the proper wires and they'll still carry the gathered power to your drone hardware. I don't…"
Mar 27
Trey Hagg replied to Anton Ludwig's discussion Transmitter and Receiver Combo?
"Receivers work by getting a signal through the air from the transmitter. There are different types of receiver signals: PPM (Pulse Position Modulation), PWM (Pulse Width Modulation), Satellite, and a few others. Most, if not all, FCs use PPM to…"
Mar 23
Trey Hagg posted a discussion

Holding an RX/TX bind

Hi, I'm building a quadcopter, and I need some assistance on a receiver-related issue.Before I explain my problem, I should probably list my hardware.Receiver: Turnigy 2.4 GHz 8chTransmitter: Turnigy 9XR Pro w/ Dsss 2.4 GHz transmitter moduleNow for my problem: My receiver binds to the transmitter with no issue, but when I unplug the battery, the receiver loses its binding to it. I'm sure this is a stupid question, but I couldn't find anything about this topic anywhere. Is there some way to…See More
Mar 22
Andre K. replied to Trey Hagg's discussion Powering a receiver with the Pixhawk
"Connect a BEC that provides 5.0 ... 5.5v to the servo rail, then Pixhawk will use it for redundancy as well."
Feb 20
Trey Hagg posted a discussion

Powering a receiver with the Pixhawk

I think I'm almost done with my drone, but I have run into a problem.So the Pixhawk doesn't supply power to the servo rail, but that is the only thing my receiver is connected to... I'm trying to research how to power the receiver without a separate battery, but I can't figure out how. Can somebody please help me? My receiver is the Turnigy 8ch 2.4Gz receiver.See More
Feb 20
Trey Hagg replied to Trey Hagg's discussion Can't get my quadcopter flying
"I recently completely dismantled my quadcopter, and now I'm going to start over. I'm going to start by doing away with the PDB I have on it (Probably should've mentioned that; It might've been the problem) and use the Flamewheels…"
Feb 17
Trey Hagg replied to Trey Hagg's discussion Can't get my quadcopter flying
"Hello all, I bought a new battery and propellers yesterday. In addition to being completely dead, the old battery was very swollen. It was on the bottom layer of the frame, so I only got to see its condition when I pried it out. I'm probably…"
Feb 14
Matej Miljko replied to Trey Hagg's discussion Can't get my quadcopter flying
"Trey, I think then the 0.5 might be in cm then :) Half inch is a huge hole. Best of luck with your build."
Feb 13

Profile Information

Please tell us a bit about your UAV interest
I have only built one drone before and I want to be a drone operator in the Air Force
Hometown:
Cincinatti

Comment Wall

  • No comments yet!

You need to be a member of DIY Drones to add comments!

Join DIY Drones

 
 
 

© 2017   Created by Chris Anderson.   Powered by

Badges  |  Report an Issue  |  Terms of Service