"Hi Gustavo,
Did you set your baud rate in XP for the arduino device? It should be 115200 for USB.
v"
Von RocK's Discussions
APM2 board no longer boots. Please Help
Started this discussion. Last reply by Von RocK Sep 3, 2012. 6 Replies 0 Likes
Hi,I'm hoping for some help. I have an APM 2.0 board. I had it installed on my DJI 550 Hex using 2.7. It worked very well. I had a hard landing, and the APM case crushed the reset button. I pulled…Continue
Von RocK's Page
Latest Activity
Von RocK replied to Von RocK's discussion APM2 board no longer boots. Please Help"I got sidetracked! I pulled a board out of one of my planes and put in in my hex copter with 2 axis camera gimbal. Everything went smooth and it's ready to fly as soon as the wind calms down. Sometimes you have to prioritize the fun…"
Monroe Lee King Jr. replied to Von RocK's discussion APM2 board no longer boots. Please Help"It should work without the reset button. Did you loose the pads on the board? If so that's bad :( Sorry to hear that. You need the pads to make the connection manually to reset the board. However if you look at the Eagle file you might be able…"
Von RocK replied to Von RocK's discussion APM2 board no longer boots. Please Help"I desoldered it. I think it went OK. The button is broken. It was not shorting out. It looks like by design the two top posts should be connected and the two bottom posts should be connected and the pressed button would short those together for the…"
Monroe Lee King Jr. replied to Von RocK's discussion APM2 board no longer boots. Please Help"Be careful ;) good luck. I think you can clip the leads (legs) on two of them (if you have fine clipers) becareful and don't lift a pad make sure it's hot enough (but not too hot)
You can hold the board upside down apply heat and let the…"
Von RocK replied to Von RocK's discussion APM2 board no longer boots. Please Help"Thank you Monroe. On closer inspection it seems that I may have only removed the top part of the button, and the two pads are currently making constant contact. That would explain the board's behaviour.
I will desolder it and see what…"
Monroe Lee King Jr. replied to Von RocK's discussion APM2 board no longer boots. Please Help"Desolder that switch from the board and clean up the pads under it. In the future short the pads to do a reset. Contact 3DR and ask if you can buy a switch to replace it (if you can replace it yourself) You can send it back for repair."
Von RocK posted a discussionAPM2 board no longer boots. Please Help
Hi,I'm hoping for some help. I have an APM 2.0 board. I had it installed on my DJI 550 Hex using 2.7. It worked very well. I had a hard landing, and the APM case crushed the reset button. I pulled the reset button apart (just the top part was crushed) and the board continued to fly really well.I tried to update to 2.7.2 yesterday. I used CLI to erase, and then did a reset. At one point the the reset function asks for a hard reset on the board. Obviously I can't do one, as the top part of the…See More
Profile Information
- About Me:
- I'm here.
- Tell us a bit about your UAV interest
- Potential commercial uses.
- Hometown:
- Calgary
Comment Wall
- No comments yet!
Social Networking
Top Content
Contests
Season Two of the Trust Time Trial (T3) Contest has now begun. The fourth round is an accuracy round for multicopters, which requires contestants to fly a cube. The deadline is April 14th.A list of all T3 contests is here.
Groups
-
Moderators
24 members
-
Documentation Editors
51 members
-
ArduRover User Group
184 members
-
Japan ArduCopter Group
51 members
-
Taiwan ROC ArduPilot Gro…
8 members
Advertisement
© 2013 Created by Chris Anderson.
Powered by
