"127.0.0.1 means the loopback device. which is always there even when not connected to a lan or wifi"
Xichen Shi's Discussions
Video Source Code
Started this discussion. Last reply by Michael Oborne Sep 9, 2012. 3 Replies 1 Like
Hello,I'm using the APM Mission Planner to help control an unmanned drone and I need to have my own video feed set up to do so. I've been trying to understand how your video feed works, especially…Continue
Possible APM burnt out. uart0 not responding, no power through output rail
Started this discussion. Last reply by Dane Aug 16, 2012. 3 Replies 0 Likes
Hi all,While I was testing APM 2.0 with my ESC which provides 5V power, I think I accidentally short the 5V and GND on sensor rail. The result is that:1. APM 2 immediately power off, no burnt smell…Continue
Xichen Shi's Page
Latest Activity
Guanyang Luo replied to Xichen Shi's discussion Video Source Code"Hello, I am from Xichen's team. We tried the method you posted, but we couldn't get the video stream when we set the Mjpeg source to the local ip address of our computer.
Since we won't have any LAN and WiFi connectection in the…"
DeveloperMichael Oborne replied to Xichen Shi's discussion Video Source Code
"the hud supports either a directshow capture device, or a mjpeg feed.
please have a look here
http://vps.oborne.me/gcs/Mjpeg%20Video%20Source%20with%20VLC.htm"
Xichen Shi posted a discussionVideo Source Code
Hello,I'm using the APM Mission Planner to help control an unmanned drone and I need to have my own video feed set up to do so. I've been trying to understand how your video feed works, especially how you can set it up with the HUD overlay, but I can't seem to crack it. Could someone explain the flow of the video feed through the program for me? I just want to know what parts I need to duplicate/mimic in my own form from the MainV2, FlightData and ConfigPlanner screens.Thanks a lotSee More
Dane replied to Xichen Shi's discussion Possible APM burnt out. uart0 not responding, no power through output rail"Perhaps I wasn't clear enough. It was late last night. I WAS able to get power through the input channel, but when running a servo splitter for power from the esc BEC's I get no power, no LEDS nothing.
So far zero response from 3dr. :/
-D"
Xichen Shi replied to Xichen Shi's discussion Possible APM burnt out. uart0 not responding, no power through output rail"Hi Dane,
Our problems are little different. I cannot get power through output or input rail (LED not lit up). And my Vcc and GND seem to be short.
I already send my APM 2.0 back to 3DR for RMA. Hopefully they can figure out a way to repair…"
Dane replied to Xichen Shi's discussion Possible APM burnt out. uart0 not responding, no power through output rail"Same issue here.
I can get power from the USB, as well as the input rail, but when powered from the output rail. The green light glows faint. None of the diodes or anything looks burned and I have never seen smoke or shorted out the APM.
Zero…"
Xichen Shi posted a discussionPossible APM burnt out. uart0 not responding, no power through output rail
Hi all,While I was testing APM 2.0 with my ESC which provides 5V power, I think I accidentally short the 5V and GND on sensor rail. The result is that:1. APM 2 immediately power off, no burnt smell and no visible burnt trace or parts.2. Board won't get power through 5V from output rail through ESC anymore3. Vcc (+ on input and sensor rail) is separated by only 33ohm from GND (which multimeter read as short)4. When plugged into USB, LED indicators light up but no uart connection I presume that I…See More
Profile Information
- About Me:
- Undergraduate in Aerospace Engineering
- Tell us a bit about your UAV interest
- Autonomous Aerial Surveillance
- Hometown:
- Shanghai, China
Comment Wall
- No comments yet!
Social Networking
Top Content
Contests
Season Two of the Trust Time Trial (T3) Contest has now begun. The fourth round is an accuracy round for multicopters, which requires contestants to fly a cube. The deadline is April 14th.A list of all T3 contests is here.
Groups
-
X8
130 members
-
Learning to program the …
315 members
-
Japan ArduCopter Group
51 members
-
ArduRover User Group
185 members
-
Documentation Editors
51 members
Advertisement
© 2013 Created by Chris Anderson.
Powered by
