"Did you try to decrease loiter speed?"
Yannick's Discussions
Arducopter V3.0.0 RC Beta Feedback Thread
Started this discussion. Last reply by Randy May 22. 3 Replies 0 Likes
I think we need a feedback thread for the new Arducopter V3 Software (beta). This is my post out of the 2.9.1b thread: Dear Randy,WPNAV_SPEED_DN & UP does not solve the problem. There must be…Continue
MP 1.2.36 (bug?) Problems
Started Mar 31 0 Replies 0 Likes
Hello!i've got a problem with mission planner.FW: 2.9.1HW: 3DR APM 2.5MP: 1.2.36 (clean install)In the hardwareoptions category the genuine 3DR PowerModule is selected and works.When i use the…Continue
APM 2.5 no USB after ESC calibration
Started this discussion. Last reply by Yannick Oct 17, 2012. 6 Replies 0 Likes
Hello all!I'm new to DIY Drones and Ardupilot.After calibrating the escs with the automatic mode, its impossible to connect the ardupilot to my computer. There is no COM device in the devicemanager…Continue
Yannick's Page
Latest Activity
Yannick replied to Craig Elder's discussion APM Copter 2.9.1.b has been released"I've got a problem regarding the log based geotagging with MissionPlanner. (RC5 and MP 1.2.53)
The log is always 4days + the real Photo date.
GPX Files do not contain a valid timestamp. The Day is right, but the time is 0:00:00.
It is…"
Yannick replied to Craig Elder's discussion APM Copter 2.9.1.b has been released"Hello David,
taking a short look into your log files, there is a voltage drop (VCC 5V) in the area around 2375."
Yannick replied to Jamie Glover's discussion Possible bug in the latest Mission Planner Release"I've got the same problem with MP 1.2.53 and Arducopter V3 RC3.
"
Yannick replied to Craig Elder's discussion APM Copter 2.9.1.b has been released"You are talking about 2.9!!! :-)
I have the slow ascending/descending since V3 RC1. Hope Randy will finde the problem. Flying a mission in more than 100m rel. alt. takes nearly two minutes to climb up. So i decided to take off and land complete…"
Yannick replied to Craig Elder's discussion APM Copter 2.9.1.b has been released"Randy, are there any news regarding the poor ascending/descending performance? (max. 0.65m/s)
Best regards from Germany,
Yannick"
Yannick replied to Craig Elder's discussion APM Copter 2.9.1.b has been released"hello Jan,
i tried your advice but it didn't work. Throttle mid was at 350, no difference.
Later i tuned Rate P and Stabilize P. Because of my Closed Loop ESCs i can raise Rate P from 0.110 to 0.16. Stabilize P from 4.0 to 5.0.
Stabilize I is…"
Yannick replied to Oliver G.'s discussion Is there a limit for DO_DIGICAM_CONTROL commands?"Oliver, you don't need an extra GPS Log for the trigger points.
Use the build-in geotag function in MissionPlanner!
http://diydrones.com/profiles/blogs/geotagging-images-with-mission-planner
It aligns GPS time and the Camera time and uses the…"
Yannick replied to Craig Elder's discussion APM Copter 2.9.1.b has been released"Dear Randy,
i'm still trying to get more information regarding this problem. I hope you keep this problem in mind, maybe you'll find the bug yourself.
Back to my ascending and descending problems in V3.
Today i did a test with my new…"
Yannick replied to Craig Elder's discussion APM Copter 2.9.1.b has been released"Wow! The next RC :) Going to test it when our rain and storm stops in the north of Germany.
Have you read my bug report? Its a quite serious problem:
There is a really big problem when switching between the different flight modes.
With Flightmodes…"
Yannick replied to Oliver G.'s discussion Is there a limit for DO_DIGICAM_CONTROL commands?"Yes Nick, that would be the best solution.
As oliver already said, triggering by time is not very useful but a trigger every 30meters would be perfect.
Maybe you can add a new Command. "Start Digicam Trigger" with one value (meters) and…"
DeveloperRandy replied to Yannick's discussion Arducopter V3.0.0 RC Beta Feedback Thread
"Mike,
It looks like the letter "H" with the motors on the tips of the letter. "H" by itself doesn't mean much, you can build an H shaped frame and fly it with the "X" configuration…"
Mike Mac replied to Yannick's discussion Arducopter V3.0.0 RC Beta Feedback Thread"
"11) add support for H-quad frame "
I thought that the H configuration was for 6 motors. What is an H quad?
"
Mark replied to Yannick's discussion Arducopter V3.0.0 RC Beta Feedback Thread"Battery monitoring doesn't work on the PX4FMU"
Yannick posted a discussionArducopter V3.0.0 RC Beta Feedback Thread
I think we need a feedback thread for the new Arducopter V3 Software (beta). This is my post out of the 2.9.1b thread: Dear Randy,WPNAV_SPEED_DN & UP does not solve the problem. There must be something wrong with the new attitude controller.I tested 10m/s horizontal speed. That was quite fast! But my Lipos are a litte old. 90A and below 12V... (4S Lipo!)Can you smooth the YAW in Auto mode? Its really rough.We are discussing the V3 Arducopter software in a german forum.There is a really big…See More
Yannick replied to Craig Elder's discussion APM Copter 2.9.1.b has been released"Dear Randy,
WPNAV_SPEED_DN & UP das not solve the problem. There must be something wrong with the new attitude controller.
I tested 10m/s horizontal speed. That was quite fast! But my Lipos are a litte old. 90A and below 12V... (4S …"
Profile Information
- Tell us a bit about your UAV interest
- Like taking pictures with uavs
Comment Wall
- No comments yet!
Social Networking
Top Content
Contests
Season Two of the Trust Time Trial (T3) Contest has now begun. The fourth round is an accuracy round for multicopters, which requires contestants to fly a cube. The deadline is April 14th.A list of all T3 contests is here.
Groups
-
ArduCopter User Group
1356 members
-
DIYDrones News Team
5 members
-
Melbourne
54 members
-
Andropilot Users Group
203 members
-
Spanish arducopter Users
88 members
Advertisement
© 2013 Created by Chris Anderson.
Powered by
