antonio
  • Male
  • arbatax
  • Italy
Share

antonio's Groups

 

antonio's Page

Latest Activity

Alexey Dobrovolskiy replied to antonio's discussion DJI N3 + remote Shutter UGCS in the group UgCS
"Important addition. Only this method (trigger in waypoint) will work. Camera by time action works only with "native" DJI cameras."
Nov 8
Alexey Dobrovolskiy replied to antonio's discussion DJI N3 + remote Shutter UGCS in the group UgCS
"Hi, I seems that we have good news for you. We managed to configure camera trigger with A3, I hope that with N3 will be the same. 1. You need to have latest DJI firmware loaded to all components. 2. In DJI Assistan 2 configure some port as…"
Nov 8
Alexey Dobrovolskiy replied to antonio's discussion DJI N3 + remote Shutter UGCS in the group UgCS
"Thank you for pointing me to Pulsekraft and Intelli-G.  Out of the box (without modifications) UgCS can't work with these solutions. But I sent messages to both companies - if they will be interested in integration may be we can do…"
Nov 2
antonio replied to antonio's discussion DJI N3 + remote Shutter UGCS in the group UgCS
"Thanks again for Alexey's response, Yes, I know Pulsekraft or Intelli-G systems. Do you refer to those? for example using a Pulsekraft system you can work with UGCS? Now I ask you a question "uncomfortable" because I think you are…"
Nov 2
Alexey Dobrovolskiy replied to antonio's discussion DJI N3 + remote Shutter UGCS in the group UgCS
"Hi Antonio,  yes, you are correct. If custom camera connected to N3/A3 autopilot using F1-F8 ports - we can't trigger it. Do you know other ground station software which can do this? Again, it's not our limitation. It's…"
Nov 2
antonio replied to antonio's discussion DJI N3 + remote Shutter UGCS in the group UgCS
"Hi Alexey, thank you for the answer however I can not believe that it is not possible to output a PWM command on any of the ports of DJI N3 when it arrives on the photogrammetry waypoints. It already had WooKong in 2011/2012 with the previous…"
Nov 2
Alexey Dobrovolskiy replied to antonio's discussion DJI N3 + remote Shutter UGCS in the group UgCS
"I'm very sorry, but it's impossible at the moment. In case of "modern" DJI drones we don't have any access to autopilot ports. We can do only what DJI allows us through their SDK."
Nov 1
antonio replied to antonio's discussion DJI N3 + remote Shutter UGCS in the group UgCS
"Hi Arturs and thanks for the reply What I do not understand is how can such a beautiful software DO NOT give consent to a F1-F8 port for remote shutter.Not everyone has a Phantom, Mavic, Inspire, Matrix ... many have Matrix with Gimbal Alexmos…"
Oct 28
Artūrs replied to antonio's discussion DJI N3 + remote Shutter UGCS in the group UgCS
"Hi Antonio, UgCS works by using DJI SDK. Most functions that are supported by DJI are supported in UgCS. As you are using a custom gimbal, I would recommend you to seek information on how to connect your gimbal or shutter control to DJI LB2. If that…"
Oct 18
antonio replied to antonio's discussion DJI N3 + remote Shutter UGCS in the group UgCS
"dear Anna thank you again Unfortunately the gimbal is third party so I thought I could not connect it to lightbridge2 (if I do not mistake the LB2 only handles DJI gimbals ... is it true?) If there is a way to connect a third-party gimbal with…"
Oct 17
Anna Moshkova replied to antonio's discussion DJI N3 + remote Shutter UGCS in the group UgCS
"Dear Antonio, Hope you are doing well. Did you try to connect Lightbridge2 to your gimbal and camera via gimbal port? Unfortunately, we have not tested this gimbal. Best regards, Anna Moshkova"
Oct 17
antonio replied to antonio's discussion DJI N3 + remote Shutter UGCS in the group UgCS
"Dear Anna thanks for my interest in my problem. :-) Gimbal is third party (NOT DJI) and run by Alexmos but this is not the problem. With the DJI Remote Control Channel Extended interface, I can control the F1-F8 ports in PWM for the management…"
Oct 16
Anna Moshkova replied to antonio's discussion DJI N3 + remote Shutter UGCS in the group UgCS
"Dear Antonio, You have the unique configuration. To understand what we can advise you in this case, please, specify some additional information: What gimbal do you use? Do you have an opportunity to control camera shutter via DJI GO?  Best…"
Oct 16
antonio added a discussion to the group UgCS
Thumbnail

DJI N3 + remote Shutter UGCS

HiI have a system composed of DJI N3 + LB2 + Remote Control Channel Extended.The "Manual" shutter set in F1 works perfectly with Extender but I'm trying to make the remote shutter via PWM (always on F1) on  UGCS but without successDo you have any help or suggestion to give me?Thank you all for the helpSee More
Oct 13

Profile Information

Please tell us a bit about your UAV interest
uav
Hometown:
arbatax

Comment Wall

  • No comments yet!

You need to be a member of DIY Drones to add comments!

Join DIY Drones

 
 
 

© 2017   Created by Chris Anderson.   Powered by

Badges  |  Report an Issue  |  Terms of Service