carlo pogs
  • Male
  • Philippines
Share

carlo pogs's Groups

 

carlo pogs's Page

Latest Activity

Flying Buddha replied to carlo pogs's discussion 2.4ghz DJI UGCS & 2.4ghz taranis x8r . is it safe to use both? in the group UgCS
"I've been using the following combinations: 1.  Taranis and the DJI 2.4 Data link for over a year once a week and have had no issues.  2. Graupner MC-32 and DJI 2.4 Data link for over two years now and have had no issues. Hope this…"
Jun 11
carlo pogs replied to carlo pogs's discussion 2.4ghz DJI UGCS & 2.4ghz taranis x8r . is it safe to use both? in the group UgCS
"Got it. Thanks."
Jun 8
Artūrs replied to carlo pogs's discussion 2.4ghz DJI UGCS & 2.4ghz taranis x8r . is it safe to use both? in the group UgCS
"We have been using DJI 2.4G Data Link with 2.4GHz Spektrum RC for a long time, there are no major issues as long as the RC is at least 3 meters away from the DataLink ground end."
Jun 8
Alexey Dobrovolskiy replied to carlo pogs's discussion 2.4ghz DJI UGCS & 2.4ghz taranis x8r . is it safe to use both? in the group UgCS
"Hi Carlo! Question is regarding interference between two radio systems? It should not be a problem - but do not use both RC controllers in close proximity to each other (<1m)."
Jun 8
carlo pogs added a discussion to the group UgCS
Thumbnail

2.4ghz DJI UGCS & 2.4ghz taranis x8r . is it safe to use both?

2.4ghz DJI UGCS & 2.4ghz taranis x8r, is it safe to use both? Or is it better to just use 2.4ghz DJI gcs w/ UGCS?Any UGCS user have try this two 2.4ghz for RC & 2.4 ghz UGCS both at the same time ?See More
Jun 8
carlo pogs replied to carlo pogs's discussion How to save current dorne position, return to home, change the batt then resume the mission to the last save position? in the group UgCS
"My plan is to separate power for FC/radio and motors. FC power consumption is very small against the motors/load. Dual power system maybe, so my FC will always stay on wile changing mainpower for motor/load."
Jun 6
Curtis replied to carlo pogs's discussion How to save current dorne position, return to home, change the batt then resume the mission to the last save position? in the group UgCS
"I basically keep an eye on the battery level and when it's low enough I pause the mission at the end of a route line and set my new start point there, fly back, change batteries and resume the mission. My current mission takes between 3…"
Jun 5
Alexey Dobrovolskiy replied to carlo pogs's discussion How to save current dorne position, return to home, change the batt then resume the mission to the last save position? in the group UgCS
"In case if it is in the middle of route generated by Photogrammetry tool or AreaScan - no way."
May 23
carlo pogs replied to carlo pogs's discussion How to save current dorne position, return to home, change the batt then resume the mission to the last save position? in the group UgCS
"Is there any way to capture that position in UgCS then add that position as a new waypoint and start (resume) from that new waypoint ?"
May 23
Alexey Dobrovolskiy replied to carlo pogs's discussion How to save current dorne position, return to home, change the batt then resume the mission to the last save position? in the group UgCS
"Hi, such scenario isn't implemented in UgCS. UgCS allows to start (resume) mission from particular waypoint of the route."
May 22
carlo pogs added a discussion to the group UgCS
Thumbnail

How to save current dorne position, return to home, change the batt then resume the mission to the last save position?

How to save current drone position, return to home, change the battery then resume the mission to the last save position?Maybe we can hover the drone for a few seconds to get accurate gps location before returning home.I cant figure it out how to do it. See More
May 22
Alexey Dobrovolskiy replied to carlo pogs's discussion How to: Waypoint turmode in UGCS just go left,right,forward & back instead of turning (yaw) in the group UgCS
"Carlo,you can download UgCS 2.11 here - https://www.ugcs.com/en/page/ugcs-version-2-11-betaDespite that it's beta it's quite good tested in the field.To keep nose direction constant during the flight you can use "Change yaw"…"
May 11
carlo pogs replied to carlo pogs's discussion How to: Waypoint turmode in UGCS just go left,right,forward & back instead of turning (yaw) in the group UgCS
"That's good. We need that feature for drone spraying. We want to avoid unnecessary turning as we don't care drone's nose direction during spraying. Thanks for the info"
May 9
Artūrs replied to carlo pogs's discussion How to: Waypoint turmode in UGCS just go left,right,forward & back instead of turning (yaw) in the group UgCS
"I have just checked and we will have the feature available in upcoming UgCS version"
May 9
Artūrs replied to carlo pogs's discussion How to: Waypoint turmode in UGCS just go left,right,forward & back instead of turning (yaw) in the group UgCS
"Hi Carlo, We have done this kind of setting for our DDC controller (https://www.youtube.com/watch?v=_OdXbgfDyPY&list=PLRfRuRLHgAaUJWB4hRQ15n62Lj8vnY1Z7) But not in regular UgCS versions. It is doable, but I must inform that only for Arducopter…"
May 9
carlo pogs added a discussion to the group UgCS
Thumbnail

How to: Waypoint turmode in UGCS just go left,right,forward & back instead of turning (yaw)

How to achieve this kind of flight where the nose will always face same direction during the mission?No need of yawing.See More
May 9

Profile Information

Please tell us a bit about your UAV interest
test
Hometown:
dc

Comment Wall

  • No comments yet!

You need to be a member of DIY Drones to add comments!

Join DIY Drones

 
 
 

© 2017   Created by Chris Anderson.   Powered by

Badges  |  Report an Issue  |  Terms of Service