"friends,
there are many smaller gps trackers doing the same ( sms back in 1 min when called, giving gps data and listen to surrounding, send googlemap link etc) in dealextreme beginning from around 23usd ranging up to 50usd... take a look...
dincer
"
dincer hepguler's Groups
-
Turkish Ardu Group
7 members
-
ArduRover User Group
207 members
-
ArduPilot (legacy) User …
130 members
dincer hepguler's Discussions
dont see any hardware tabs in my mission planner
Started this discussion. Last reply by dincer hepguler May 26. 2 Replies 0 Likes
dincer hepguler's Page
Latest Activity
dincer hepguler commented on Bob Doiron's blog post 9x gets 3DR 915 MHz air module"great job... cudos... i am also waiting anxiously for your instructable for how to do it.. detailed photos at least...
dincer"
dincer hepguler replied to dincer hepguler's discussion dont see any hardware tabs in my mission planner"@Thomas,
no i didnt... i just run MP as i said and it tried to update.. i did the update to MP 1.2.51 and after launching , saw that there was not any hardware options tab in config... it was there before when i first installed MP1.2.33 without…"
AdminThomas J Coyle III replied to dincer hepguler's discussion dont see any hardware tabs in my mission planner
"@dincer,
Did you establish a Mavlink connection with your APM2.5 and download it with Ardupilot code prior to trying to use the configuration tab to set up your hardware?
Regards,
TCIII"
dincer hepguler posted a discussiondont see any hardware tabs in my mission planner
i had MP 1.2.33 installed on my pc and yesterday i run it first time to test my APM2.5 for my rover project. it told me that there were an update awailable when i run MP. i did the update and it updated to version 1.2.51.. but now i cannot see any hardware options on my config tab. there is only 3dr radio, antenna tracker, planner tabs there... i was planning to add a Maxbotics ez1 sonar... i uninstalled andf reverted to previous 1.2.33 version but the result is the same. any ideas?.. i am a…See More
dincer hepguler replied to melis ayse's discussion apm 2.5 motor sürme in the group Turkish Ardu Group"Melis hanım,
Size kendi 2dc motorlu robotik tank projemde kullandigim kodu ekledim. eger incelerseniz dc motor surme ile ilgili yardımı olur. bu robotda apm1 in serbest pinlerini kullandım ve bu kod çalısıyor...
saygılar,
Dincer
"
dincer hepguler replied to melis ayse's discussion apm 2.5 motor sürme in the group Turkish Ardu Group"Melis hanım,
Arduino uno için verdiginiz kod dc motor degil servo çalistirmak icindir. 9nolu pine bagli bir servoyu hareket ettiriyor. oncelikle kodu bir servo ile deneyin. ayrıca APM bazi pinleri kendi kontrol ediyor, 9nolu pin…"
dincer hepguler replied to Mike Wilson's discussion Mike's ArduRover Build Log in the group ArduRover User Group"thanks for the responses...
@Thomas
so i cant use a pwm based sensor for the time being... i also have Maxbotics EZ1 at hand. can i use it?... i had bad experiences with that sensor in my previous Arduino based robotics projects ( inconsistent…"
Profile Information
- About Me:
- robotics hobbyist and enthusiast. 3D Graphics and design. Nature lover, bonsai maker...
- Tell us a bit about your UAV interest
- borsaci06.com
- Hometown:
- ankara - turkey
dincer hepguler's Videos
Dincer hepguler's Blog
incredibly cheap OSD from Hobbyking...
Posted on July 16, 2011 at 7:30am 3 Comments 2 Likes
friends,
has anyone seen this?... http://www.hobbyking.com/hobbyking/store/__17141__HobbyKing_G_OSD_On_Screen_Display_with_GPS.html
a very small osd at $36 with the gps module included... it…
Continue Solar Falcon first attempt with ArduPilot and Nunchuck Acc
Posted on May 1, 2009 at 5:30am 15 Comments 0 Likes
system: 35 mhz 6 ch radio (because im planning to use 900mhz x-bees for telemetry and 2.4ghz video downlink), solar wing with ailerons, planned to use APv1 on throttle and rudder. stabilization on ailerons… Continue
Comment Wall (4 comments)
- At 3:19pm on April 28, 2009,
Ugur Bozkurt said… - merhaba,
uav ile ilgili bir tez hazirliyorum. fakat sensor kalibrasyonu icin osiloskopta bazi olcumler yapmamiz gerekiyor. co pilot sensorunun ne kadar dondugune bagli olarak bir cikis gozlemlememiz gerekiyor. servonun nasil tepki verdigi yani.
kullandigimiz aletler cpd4(fma co pilot), sub micro servos, lipo batterry, dx6i radio controller.
gerek baglanti gerek osiloskoptan aldigimiz bilgi olsun ne yapmamiz gerektigi hakkinda pek fazla bilgimiz yok.
bu konuda yardiminiza ihtiyacimiz var..
tesekkurler.
- At 2:51am on May 2, 2009,
Reto said… - Hi Dincer. I feel I am only a good DIYer when things are running like I'd like to. But I spend more time on things that aren't!! It's the learning process I like, I think. Good luck with your progress
- At 5:12am on May 2, 2009, Reto said…
- Same goal to auto-land with EZ1 sensor but code space is getting scarce, even with 2 boards. Maybe with one AP 328 (I got already but didn't prepare it yet) and one AP 168 it will be ok. Or I'll add a spare Arduino Pro Mini, it weights almost nothing.
- At 5:39am on May 2, 2009, Reto said…
- I am not so advanced with autolanding. It's just in my head. You should start a permanent blog in which you could describe it, show your problems and progress. Would be nice to follow.
Social Networking
Top Content
Contests
Season Two of the Trust Time Trial (T3) Contest has now begun. The fourth round is an accuracy round for multicopters, which requires contestants to fly a cube. The deadline is April 14th.A list of all T3 contests is here.
Groups
-
Andropilot Users Group
203 members
-
Moderators
24 members
-
ArduRover User Group
207 members
-
Japan ArduCopter Group
58 members
-
ArduCopter User Group
1355 members
Advertisement
© 2013 Created by Chris Anderson.
Powered by
