"Hi everyone, I really want to know If I wanted to supply power to my APM v1.4 through VIN pin using a 7.2v adaptor then what shoudl be the max current (amp) of the adaptor ?"
-
kasra.mirshamsi
- Male
- Leicester
- United Kingdom
- Blog Posts
- Discussions (16)
- Groups (2)
- Photos
- Photo Albums
- Videos
kasra.mirshamsi's Groups
-
ArduCopter User Group
1289 members
-
ArduPlane User Group
684 members
kasra.mirshamsi's Discussions
accelerometer (gx gy gz) readings
Started this discussion. Last reply by kasra.mirshamsi Apr 20, 2012. 2 Replies 0 Likes
Hi folks, does anyone has any explanation why when the AMP/IMU board is static still the values of gx gy gz changes, should't they remain at zero. The intresting thing is that on CLI test mode I get…Continue
kasra.mirshamsi's Page
Latest Activity
"Hi everyone, I really want to know If I wanted to supply power to my APM v1.4 through VIN pin by 7.2v adaptor then what should be the max current (amp) of the adaptor ?"
"Hi everyone, I really want to know If I wanted to supply power to my APM v1.4 through VIN pin using a 7.2v adaptor then what shoudl be the max current (amp) of the adaptor ?"
"Oh yes, It is working, always appreciated your suggestions."
"Thanks chris, I will give that a try and come back with feedback."
"I am Soldering it. "
"Hi Chris: finally I have received my replaced HMC5883L mag sensor, but again I am facing the same problem.
I am trying to setup the Compass in CLI mode but the compass initialization fails. I cannot enable the compass. This…"
"Hi guys, I came late to this debate its been 3 years. I read all your comments about what acce sensor measures and understand that it measures specific torques\accelerations, every force except the gravity.
Here is m y situation, I have a 3 axis…"
"Thanks aaron, I did not solder it, the DIY soldered but as long as I am looking carefully on the board, I don’t see any shorted pins. Another weird thingis that I get a smoth gx, gy and gz responses when…"
Aaron Curtis replied to kasra.mirshamsi's discussion accelerometer (gx gy gz) readings"That is bizarre! Could you have shorted something when soldering?"
accelerometer (gx gy gz) readings
Hi folks, does anyone has any explanation why when the AMP/IMU board is static still the values of gx gy gz changes, should't they remain at zero. The intresting thing is that on CLI test mode I get zero values for gx gy ang gz while on the flight tab they start vary. see below. Any Idea.?? See More
"I am using HMC5883L sensor and it does not have that faulty 200 resistor (called 204). I also uploaded the AP_Compass_test and trying to observe the compass response through the arduino IDE serial monitor, but still I get compass failed. Any…"
"Hi, I need a help regarding to my mag sensor. I connected the Mag sensor to IMU sheild based on method 2 given on the website. I am pretty sure about the wiring and I have uploaded the arduplane code v 2.3 through adruino…"
"yea my bad, I just turn off my wi fi and my phone lost its GPS. "
"Hi there, Why the iphone 4 GPS module (iGPS-360) locks even indoor and much faster compare to this Mediateck 3329 module which strugggles a lot to lock indoor If it is left 1 hour next to the window.!!!…"
Profile Information
- About Me:
- aerospace engineer (flight dynamics and control)
- Tell us a bit about your UAV interest
- Autopilot Design using vision based sensory
- Hometown:
- Leicester
Comment Wall
- No comments yet!
Social Networking
Top Content
Contests
Season Two of the Trust Time Trial (T3) Contest has now begun. The fourth round is an accuracy round for multicopters, which requires contestants to fly a cube. The deadline is April 14th.A list of all T3 contests is here.
Groups
-
Swiss Drone Group
9 members
-
ArduCopter User Group
1289 members
-
ArduCopter Evolution Team
140 members
-
Learning to program the …
313 members
-
ArduIMU Gimbal Controller
44 members
Advertisement
© 2013 Created by Chris Anderson.
Powered by
