"Holy sh!t! That's a bad one. I really wish I hadn't clicked the rest of the story. You basically killed my lunch (at least until I get that out of my mind).."
-
Lebdog
- Male
- Los Angeles, CA
- United States
- Blog Posts
- Discussions (32)
- Groups
- Photos (8)
- Photo Albums (1)
- Videos (1)
Lebdog's Discussions
Updating Firmware Mav9 - Update Failed Lost Sync
Started this discussion. Last reply by Michael Oborne Nov 11, 2012. 1 Reply 0 Likes
I was updating my firmware on my Arducopter APM V1 board, and got an update failed lost sync message. Now I am unable to connect to my Arducopter APM V1 board at all:-( I was using USB with Mav9…Continue
DROIDWORX CX4 with Arducopter & FPV
Started this discussion. Last reply by Jason Jarvis Apr 7, 2012. 26 Replies 1 Like
Well, I pulled the trigger and ordered a Droidworx CX4 airframe a few weeks ago. I have been researching and contemplating this build for a while now and am really taking my time...I already have a…Continue
Tags: gaui, gaui500x, waypoints, arducopter, droidworx
Lebdog's Page
Latest Activity
Lebdog replied to Assaf Weiss's discussion Latest arducopter firmware for APM1 1280 boaed"What is the latest firmware you have gotten to upload, verify and connect with MAVLink properly if you don't mind me asking?? I have an APM1 board also I would like to upgrade to the latest stable firmware also.
Thanks, Caleb"
Lebdog commented on M.S. IBN SEDDIK's blog post Today I tried my quadcopter, but I didn't like it..."I read your story and scrolled up to see what kind of radio you were using and instantly recognized the culprit. I had an Optic6 with which I lost several aircraft due to glitching. I am sorry for the damage to your Quad, but I was not…"
DeveloperMichael Oborne replied to Lebdog's discussion Updating Firmware Mav9 - Update Failed Lost Sync
"try a diffrent usb port. and also unplug things from the apm"
Lebdog posted a discussionUpdating Firmware Mav9 - Update Failed Lost Sync
I was updating my firmware on my Arducopter APM V1 board, and got an update failed lost sync message. Now I am unable to connect to my Arducopter APM V1 board at all:-( I was using USB with Mav9 because I coulnd't connect using the newer Mav. Does anyone know of a way to get the board to connect again??See More
Owen Booth replied to Lebdog's discussion DROIDWORX CX4 with Arducopter & FPV"Hey DaveyWavey, what motors are you running on your CX4 mate? I'm getting one this week for the good bastards at Droidworx, can't wait, but don't want to spend US$100 a piece on Axi motors :("
Lebdog replied to Lebdog's discussion DROIDWORX CX4 with Arducopter & FPV"I love this paragraph:
BEFORE EVERY FLIGHT: Before you take off, hold your aircraft in your hands and switch to stabilize mode, then pitch and tilt the plane it to confirm that the control surfaces move the correct way to return it to level flight.…"
Lebdog replied to Lebdog's discussion DROIDWORX CX4 with Arducopter & FPV"The GPS works just fine through the painted canopy:)"
Lebdog replied to Lebdog's discussion DROIDWORX CX4 with Arducopter & FPV"The gritty sound is something created by the sound passing though the carbon fiber tubes to the center plates. It's much quieter with props than without for some reason..
"
Lebdog replied to Lebdog's discussion DROIDWORX CX4 with Arducopter & FPV"I swapped in some APC 12x3.8 props today, I don't need the power of the 12x6 props right now. I ordered these props in glass and carbon fiber. I will only use the carbon ones for display for the most part..Well, I am very happy to…"
Lebdog replied to Lebdog's discussion DROIDWORX CX4 with Arducopter & FPV"Well, I spent some time looking at how I can put another center plate on top of the speed controller/power distributer plate and ended up just using stacked double sided tape. I hope the tape works well for vibration too.After connecting the…"
Lebdog replied to Lebdog's discussion DROIDWORX CX4 with Arducopter & FPV"Ok, well the AVROTO motors are tested with the BL2 ESC, but I am not too impressed with these motors so far. Basically, they are advertised for A/V specialty, yet they make a lot of noise, even without having a prop on them. The…"
Lebdog replied to Chris Anderson's discussion ArduCopter 2.3 released"3 mistakes ONLY applies to airplanes (IMO). In airplanes, I totally agree. Especially when taking a plane for a maiden flight so you can trim without sweating it. All the trainers I have used for heli's get you to hover from…"
Profile Information
- About Me:
- r/c planes, rock climbing, music, motorcycle riding and photography
- Tell us a bit about your UAV interest
- Drone video & flying with waypoints. Learning the technology. I see drones as using all many of my skills combined (r/c flying, computers & electronics).
- Hometown:
- Century City
Lebdog's Photos
Comment Wall
- No comments yet!
Social Networking
Top Content
Contests
Season Two of the Trust Time Trial (T3) Contest has now begun. The fourth round is an accuracy round for multicopters, which requires contestants to fly a cube. The deadline is April 14th.A list of all T3 contests is here.
Groups
-
DIYDrones News Team
5 members
-
ArduCopter User Group
1356 members
-
Melbourne
54 members
-
Andropilot Users Group
203 members
-
Spanish arducopter Users
88 members
Advertisement
© 2013 Created by Chris Anderson.
Powered by
