"Thanks Richard!!! I will try and report back.,"
marcelo's Groups
-
Andropilot Users Group
182 members
-
Spanish Photogrametry gr…
43 members
-
ArduCopter User Group
1293 members
marcelo's Discussions
Compensate PIDS for too powerful motors?
Started this discussion. Last reply by marcelo Mar 25. 2 Replies 0 Likes
Hi Is there any hint you can give me maybe in PID tunning to compensate for too much powerfull motors for a frame,motors= NTM 2826 1200kv, prop 8x47 and fram DJI flamewheelmy friend cannot hover due…Continue
Wrong Current measures
Started Mar 23 0 Replies 0 Likes
HelloI have installed attopilot compatible, all goes ok but current vales are higher than expected, voltages are ok... what can be wrong? or how to tune up?I m using rctimer voltage and current, my…Continue
Explain Baro ALT - Mix Alt - Gps Alt combination
Started Mar 15 0 Replies 0 Likes
Please can anyone explain a bit, how are all altitude measurements related each other to command the copter in nav, alt hold or loiter?I need to know if my CRASH was caused by improper baro covering…Continue
Turnigy HAL motors 4006 530Kv arduflyer 2.5 and 2.9.1
Started Mar 10 0 Replies 0 Likes
HelloAnyone with a similar setup, can share parameters for a nice flight (specially loiter and auto modes)I have perfect antivibration checked with raw, covered the baro sensor, using 12x45 and…Continue
marcelo's Page
Latest Activity
marcelo replied to Dan Gray's discussion APM Log Visualizer Source Code"when I click in the map, the URL being created contains "," instead of "." in the coordinates, this is due to regional settings in my computer i think, in order to avoid incorrect mapping, the url should be fixed maybe with a…"
Richard Boyhan replied to marcelo's discussion Compensate PIDS for too powerful motors?"Try tuning down the PIDs for P and IMAX in stabilize mode. The default values are P=4.5 and IMAX=8. Try 3 and 6 and see if that doesn't help. If not try lowering the values. Keep a 2 to 1 for IMAX to P. Good luck. When I run 4S battery I get…"
marcelo posted a discussionCompensate PIDS for too powerful motors?
Hi Is there any hint you can give me maybe in PID tunning to compensate for too much powerfull motors for a frame,motors= NTM 2826 1200kv, prop 8x47 and fram DJI flamewheelmy friend cannot hover due to climb as a rocket!! on 4000 4s, do not have 3s bats)See More
marcelo posted a discussionWrong Current measures
HelloI have installed attopilot compatible, all goes ok but current vales are higher than expected, voltages are ok... what can be wrong? or how to tune up?I m using rctimer voltage and current, my apm is 2.5, using 5000mha 4s, using default A1 and A2, and measured 5.3 vol in the ESC , using in Mission planner:Attopilot 90AAPM2.5 non 3DRand APM input volt 4,65 to adecuate to my multimiter readingany help?See More
marcelo posted a discussionExplain Baro ALT - Mix Alt - Gps Alt combination
Please can anyone explain a bit, how are all altitude measurements related each other to command the copter in nav, alt hold or loiter?I need to know if my CRASH was caused by improper baro covering from light and or wind...the mission was planned to 80mts max , but the copter ascended to 450mt!!!!in this graph i show some strange baro reading going suddenly very low ....…See More
marcelo replied to Jamie Ahmed's discussion APM2.5 voltage monitor w/o Attopilot sensor? in the group ArduCopter User Group"TUFAN, how many OHMS for the trimpot?"
marcelo replied to mc_don's discussion NX-4006-530kv on arducopter"I do 20mins with turnigy hal frame and a 5000mah 30c bat, but anyone would like to share pids for similar setup?"
marcelo replied to Randy's discussion ArduCopter 2.9 / 2.9.1 released"Marco yes i will, but tried with radio telemetry turned off, and same behaviour,,, only thing should be pids and wind"
marcelo replied to Randy's discussion ArduCopter 2.9 / 2.9.1 released"mi vibration range... very low i think
Upload Files
"
marcelo replied to Randy's discussion ArduCopter 2.9 / 2.9.1 released"yes me!!! I have my quad setup with 2.9.1 , rctimer arduflyer 2.5 , baro covered, turnigy hal frame, 12x45 prop, motors hk 4006 530kv, default pids, stabilize works 100% ok, but im having trouble with loiter (it is slightly climbing)...sometimes…"
marcelo replied to Andrew Tridgell's discussion delay in shipping 433MHz radios due to USB interference problem"Well I have rctime 433 usb , it is not clear to me how can I fix the problem, I have a very bad range connecting the usb telemetry to my laptop, what can be done?"
marcelo replied to marcelo's discussion 4 motors turned off xquad auto mission"problem seems to be radio signal lost due to antena 2.4 problem in my TX.... the apm turned motors off i think related to failsafe , i have rx frsky v8 as receiver.... what SHOULD I DO TO CONFIGURE FAIL SAFE IN THE RECEIVER AND IN THE APM? to…"
marcelo posted a discussion4 motors turned off xquad auto mission
Hello please I want to know reasons/problems that may exist for 2.8 default code turned off my copter initiating a missionI must admit my radio2.4 antena was loose when happened...is this related to fail safe or similar? I have all settings default.See More
Profile Information
- About Me:
- none to say just quads fan
- Tell us a bit about your UAV interest
- quads
- Hometown:
- san isidro argentine
Comment Wall
- No comments yet!
Social Networking
Top Content
Contests
Season Two of the Trust Time Trial (T3) Contest has now begun. The fourth round is an accuracy round for multicopters, which requires contestants to fly a cube. The deadline is April 14th.A list of all T3 contests is here.
Groups
-
ArduRover User Group
185 members
-
Turkish Ardu Group
6 members
-
Agricultural UAVs
129 members
-
ArduCopter Italian Group
87 members
-
Moderators
24 members
Advertisement
© 2013 Created by Chris Anderson.
Powered by
