"Yes my throttle is reversed and mission planner shows the minimum 1000.
I will try your solution.
Do you believe that the PPM encoder could solve my problem??
Thank you very much Dave
"
nina eyes's Discussions
Project change (Y6 =>Quad) and problem!
Started this discussion. Last reply by nina eyes Apr 19, 2012. 9 Replies 0 Likes
Hello I changed drone, I started a project with an Y6 I changed to a quad. My APM board was configured for Y6, when I changed drone, I download the firmware for the quad. I recalibrate my remote…Continue
Configuration yaw
Started Apr 16, 2012 0 Replies 0 Likes
HelloI would like to have help for the configuration of the YAW in APM planner.It seems that the engines turning too quickly when I play with the YAW...(or two engines turn instead of one (but I'm…Continue
Tags: yaw, configuration
nina eyes's Page
Latest Activity
Dave replied to nina eyes's discussion Project change (Y6 =>Quad) and problem!"Does Mission Planner show the throttle at minimum setting? You may need to reverse your throttle.
Otherwise, you might have struck a known bug in the APM2 which they hope to fix shortly. A workaround is, after you plug in the LiPo and…"
nina eyes replied to nina eyes's discussion Project change (Y6 =>Quad) and problem!"And these are rapid beeps,
I did an erase on the eeprom and it y always beeps when I plug.
I think that the problem is that the engines believe that there is an acceleration.
I set my remote control...
"
nina eyes replied to nina eyes's discussion Project change (Y6 =>Quad) and problem!"Dave,
Here's the equipment I use:
APM2 card: http://code.google.com/p/arducopter/wiki/AC2Assembly
ESC HobbyKing Turnigy 45A
Motors: AXI model 281420 370W
Remote control: Futaba T8FG Super 2, 4 GHz 14ch transmitter / / RC R6208SB 8ch…"
nina eyes replied to nina eyes's discussion Project change (Y6 =>Quad) and problem!"Dave
I will give you more information on the equipment used tomorrow. as soon as I get to my internship site I give you this information immediately.
Dave thank you very much for helping me"
Dave replied to nina eyes's discussion Project change (Y6 =>Quad) and problem!"Could you supply a bit more info about your quad including APM1 or 2, what ESC's, do you have a PDB, is the beeping regular and fast or slow ...
Have you tried a complete reload of the firmware? Sometimes it doesn't get it right."
nina eyes replied to nina eyes's discussion Project change (Y6 =>Quad) and problem!"Hello Dave
Thank you for answering me, I thought that nobody wanted to answer me
My LIPO is full charged
My ESC are connected on the right pins
Engines beep all the time as if I had put the gas on top (but I'm not sure why they beep)
I think…"
Dave replied to nina eyes's discussion Project change (Y6 =>Quad) and problem!"If the APM shows that it's arming, sounds like the firmware is running OK and your RC is talking to it correctly.
ESC's generally beep because they are not receiving a (correct) signal. I'd suggest you double-check the ESC…"
nina eyes replied to nina eyes's discussion Project change (Y6 =>Quad) and problem!"When I plug my ESC DIRECTLY on the RC there is no problem! if can't come CSE, where it just?
ps: sorry for my expression"
nina eyes posted a discussionProject change (Y6 =>Quad) and problem!
Hello I changed drone, I started a project with an Y6 I changed to a quad. My APM board was configured for Y6, when I changed drone, I download the firmware for the quad. I recalibrate my remote control, my motors. When I plug the lipo, the motors start to beep all the time .. If I push the stick (yaw) to the right, the green LED is blocked. Yet I push the gas, the engine continues to beep, and does not accelerate .. May be that the engines are not calibrated? When I want to automatically…See More
nina eyes posted a discussionConfiguration yaw
HelloI would like to have help for the configuration of the YAW in APM planner.It seems that the engines turning too quickly when I play with the YAW...(or two engines turn instead of one (but I'm not sure))If someone could me helped, I thank you in advance!I have a small Y6 and I think that the PID of the software is for a larger Y6the configuration is in the enclosureThank you !NinaSee More
Profile Information
- About Me:
- beginner
- Tell us a bit about your UAV interest
- Y6
Comment Wall
- No comments yet!
Social Networking
Top Content
Contests
Season Two of the Trust Time Trial (T3) Contest has now begun. The fourth round is an accuracy round for multicopters, which requires contestants to fly a cube. The deadline is April 14th.A list of all T3 contests is here.
Groups
-
ArduCopter User Group
1282 members
-
ArduPlane User Group
675 members
-
Turkish Ardu Group
5 members
-
ArduRover User Group
183 members
-
Terrain/Surface Mapping
116 members
Advertisement
© 2013 Created by Chris Anderson.
Powered by
