"Mine started working the next day. I don't know what fixed it though."
solaris1201's Discussions
Cannot access dataflash
Started this discussion. Last reply by solaris1201 May 7, 2012. 6 Replies 0 Likes
After a somewhat hard landing, i am no longer able to read the flash card. I get the following error as soon as I try to download logs or do the logging test from CLI"ERR: No dataflash inserted"I…Continue
Motor not spinning
Started this discussion. Last reply by solaris1201 Mar 8, 2012. 6 Replies 0 Likes
I have a strange problem on my APM2 quadcopter. It is running lated code 2.4.1 It was working fine the first day, took it out in and flew with no problems. But today, I cannot get it to spin the…Continue
solaris1201's Page
Latest Activity
3D RoboticsChris Anderson replied to solaris1201's discussion Cannot access dataflash
"I'll check in to see what the delay is. "
Andke replied to solaris1201's discussion Cannot access dataflash"I wrote to support on the very day you suggested I did - no reply yet."
3D RoboticsChris Anderson replied to solaris1201's discussion Cannot access dataflash
"Contact customer support: help@3drobotics.com"
Andke replied to solaris1201's discussion Cannot access dataflash"same problem here, but no crash, just a new APM2"
Michael replied to solaris1201's discussion Cannot access dataflash"Did you fix the problem? I have the same issue, but without a crash."
solaris1201 posted a discussionCannot access dataflash
After a somewhat hard landing, i am no longer able to read the flash card. I get the following error as soon as I try to download logs or do the logging test from CLI"ERR: No dataflash inserted"I have tried reinserting the card, erasing eeprom, re-uploading firmware, reset from CLI, none of this has helped.Any advice?See More
solaris1201 replied to Mark Zimmerman's discussion ArduCopter cannot fly anyway"Are you sure the motors are spinning the right direction?"
solaris1201 replied to solaris1201's discussion Motor not spinning"thanks.i have done that and there is no motor spin. but after that I reset the board to factory defaults, then re-installed the firmware. Now it is working, i am not sure if that's what fixed it."
RickP replied to solaris1201's discussion Motor not spinning"'setup' then 'motors'. If you're at 2.4.1 it should spin them in order. Be very careful..."
solaris1201 replied to solaris1201's discussion Motor not spinning"I don't know how to do the motor test. I couldn't find the command in the CLI in the 'test' menu."
solaris1201 replied to solaris1201's discussion Motor not spinning"thanks. I have also done the transmitter calibration, but it didn't fix for me."
Robert Rhoden replied to solaris1201's discussion Motor not spinning"Similar issue this evening, I did the transmitter calibration again and everything started working again. "
solaris1201 posted a discussionMotor not spinning
I have a strange problem on my APM2 quadcopter. It is running lated code 2.4.1 It was working fine the first day, took it out in and flew with no problems. But today, I cannot get it to spin the motors.I hear the normal ESC beeps, when I arm the motors with the throttle stick all the way down and right I see the LEDs blinking as it did before. The Red LED would then stay solid incdicating motors are armed. But there is no response by the motors when I increase the throttle.So I connected the…See More
Profile Information
- About Me:
- Nothing interesting
- Tell us a bit about your UAV interest
- Starting
Comment Wall
- No comments yet!
Social Networking
Top Content
Contests
Season Two of the Trust Time Trial (T3) Contest has now begun. The fourth round is an accuracy round for multicopters, which requires contestants to fly a cube. The deadline is April 14th.A list of all T3 contests is here.
Groups
-
Documentation Editors
51 members
-
Moderators
24 members
-
ArduCopter User Group
1297 members
-
Australia
79 members
-
Andropilot Users Group
183 members
Advertisement
© 2013 Created by Chris Anderson.
Powered by
