"I am also facing the same problem. Any help ?"
tim's Discussions
Ardupilot mega stabilize mode not working and xbee not transmitting (I have very detailed info).
Started Sep 21, 2011 0 Replies 0 Likes
Hi Everyone,I need your help with the following issue that is stopping me from doing any progress.I have installed the APM software and reset the board.Please refer to the document I have attached as…Continue
Tags: (I, transmitting, have, very, info).
Ardupilot mega no servo movement in stabilize mode
Started this discussion. Last reply by U2 Jan 23, 2012. 1 Reply 0 Likes
I have run in to the following problem with ardupilot mega :I have installed ArduPilotMega1.02 and 2.1 and got the same problem.Setup the radio and configured the first 4 channels.Setup the…Continue
Ardupilot mega no servo movement in stabilize mode
Started this discussion. Last reply by Gent Armedo Sep 20, 2011. 1 Reply 0 Likes
I have run in to the following problem with ardupilot mega :I have installed ArduPilotMega1.02 and 2.1 and got the same problem.Setup the radio and configured the first 4 channels.Setup the modes and…Continue
Power Supply ... ArduPilot Mega
Started this discussion. Last reply by Johann Van Niekerk Jan 1, 2011. 2 Replies 0 Likes
In the section :Connecting your RC equipmentI have read the following line :ArduPilot Mega gets its power from the RC system.But how does it do that.When I have my USB connected, the board is powered…Continue
tim's Page
Latest Activity
Wiki NinjaGent Armedo replied to tim's discussion Ardupilot mega no servo movement in stabilize mode
"Hi Tim,
I got the same problem before but I upgraded to 2.24 and it all went away. see this thread: http://diydrones.com/forum/topics/helo-needed-on-apm-fight-mode-on-stabilize-no-servo-movements-and?xg_source=activity
and this:…"
Johann Van Niekerk replied to tim's discussion Power Supply ... ArduPilot Mega"I wanted to know the same but I had different result, when I plug 2 servos in and my receiver then the APM board powers my receiver from the USB port.... (AR7000 receiver ) and it powers it thru any port is that good or bad?"
3D RoboticsChris Anderson replied to tim's discussion Using XStream™ OEM RF Module - Help Needed..
"Maybe some RS232-to-TTL data-level converter. But it's gnarly stuff and not supported."
tim replied to tim's discussion Using XStream™ OEM RF Module - Help Needed.."There must be some way to connect them."
3D RoboticsChris Anderson replied to tim's discussion Using XStream™ OEM RF Module - Help Needed..
"This won't work. APM, like all RC electronics, can only use TTL-level serial. Ie, not DB-9 RS-232."
3D RoboticsChris Anderson replied to tim's discussion Power Supply ... ArduPilot Mega
"Your RC system is normally powered by an LiPo and ESC in the case of an electric aircraft or stand-alone battery in the case of gas. That's how APM should get its power in the plane, too. The USB is only for the benchtop."
Profile Information
- About Me:
- Software developer.
- Tell us a bit about your UAV interest
- ArduPilot Mega
- Hometown:
- Water
Comment Wall
- No comments yet!
Social Networking
Top Content
Contests
Season Two of the Trust Time Trial (T3) Contest has now begun. The fourth round is an accuracy round for multicopters, which requires contestants to fly a cube. The deadline is April 14th.A list of all T3 contests is here.
Groups
-
ArduCopter User Group
1283 members
-
ArduRover User Group
183 members
-
ArduPlane User Group
675 members
-
Turkish Ardu Group
5 members
-
Terrain/Surface Mapping
116 members
Advertisement
© 2013 Created by Chris Anderson.
Powered by
