After 4 months of work we finish to port AP_HAL library to VR Brain.
so now we are ready for test Arduplane on VRBrain and see our VR Plane fligh in the sky :)
In this video you can see only first test that we doing last week.
Our configuration are :
Added by Roberto Navoni on April 30, 2013 at 3:13pm — No Comments
Alma, Québec – April 22nd, 2013 - The municipal Council of Alma, Unmanned Systems Canada, the Alma Airport authorities and the Unmanned Aerial System Center of Excellence are proud to invite you to the 2013 Unmanned Systems Canada Student UAV Competition.
Close to a…Continue
WASHINGTON — Thousands of unmanned aircraft systems – commonly known as drones –…
A FRENCH postgraduate student has completed seven months research at Harper Adams University developing an unmanned aircraft for…Continue
Hey everyone! We finally got a small shipment of these in and have a few left. Available now at www.aeroworksproductions.com Specs are available on our website.Continue
Hi there welcome back,
Here is a little picture of the first version of my quad hybrid projet
It's a version to allow "Maxime carrier" to crash it 1 or 2 time before it's broke XD.
The design of the 2 rotating propeler is pending until i got the missing part. beteween 2…Continue
I was asked to come film in avoriaz, france to film for the volcom rail jam, video above.
I have flown in snow storms and temperatures down to minus 10 with no problems, but i discovered on this day is the dangers of "freezing fog". You can see from the video that it was only snowing a little, wind was gentle and it was a positively warm 5 degrees. I…Continue
Added by Luiz Amadeu Coutinho on April 29, 2013 at 2:00am — No Comments
I've flown a lot of different planes while working on ArduPlane, but it wasn't till yesterday that I first flew what is perhaps the most popular plane for new ArduPlane users - the Bixler2.
While setting it up on Saturday evening I had a bit of a look through some Bixler build logs in the forums, and I was surprised to find that none of the suggested ways of mounting the APM were really…Continue
See what happens if two APM powered quads get too close to each other.
The innocent ArcticCoper was in loiter, the TBS Discovery was in stabilized trying to get close up. Slow motion footage shows how one motor of the AcrticCopter completely stops after hitting the TBS Discovery quad. The damaged propeller then drags one arm down of the TBS…Continue
In the middle of a national debate on the value of commercial UAS usage I found it refreshing to see a positive spin from a major news outlet. The video leads in with a snippet about event security and then moves to show off some neat applications that many of us have seen in the past. All in all a positive showing on CNN. We need more of these!
Airspeed control is critical when flying sailplanes. You want to fly close to stall but never beyond it, since that will normally cause a tip stall and great loss of energy. How do you teach an autopilot to fly on the edge of stall?…
Hope you guys helps me to improve the design. There is a lot of things to do before it's done. For example battery holder, in different alternative…Continue
New ArduCopter, ArduPlane and ArduRover Wikis are Operational (provisionally)
The old existing Wiki(s) are no longer getting updated on a continuous basis so you need to start using the new Wiki(s).
During this transition you will need to use both of them (although for the PX4, the new…Continue
This is main board normally put on Gimbal frame near the Quad .
This is the two…Continue
I have been looking into my own method of mounting the APM with antivibration in mind.
To this end I wanted to source some freely available components specifically designed to reduce vibration.
I found a couple of such products which I am hoping will be ideal.
These coupled with a custom…Continue
As is customary and traditional, we celebrate every new 1,000 members here and share the traffic stats. This time it's 38,000!
There were almost 1.9 million page views in the last month! (we get around 65,000 pageviews a day on average). It took us just 22 days to get this latest 1,000 members--we're…Continue
I’d like to share my experience with my copter (aka ZuCopter) during my first full test using AUTO mode. My quad is ArduCopter, 3DRobotics Quad-C frame using APM 2.5 Firmware 2.9.1b
The plan was to go around the house, full automated, including takeoff and landing. This was executed quite smoothly at the first run J, Then I said… let’s try that again;…Continue