Remzibi OSD now in stock at the DIY Drones store

Hi everybody! I'm very happy to announce that the Remzibi OSD DIY Drones variant is now in stock in the DIY Drones store!

Our version is fully compatible with the original design and will work with Happy Killmore's config tool.

Our price is $89.99, this includes a custom FTDI programming cable and a set of pin headers.

Links and full feature list are available on the product page.

We hope you enjoy this one, and as always, feedback is welcome!

Views: 6217

Tags: DIY Drones store, OSD, Remzibi OSD, RemzibiOSD, Video

Comment by Ed Kirk on January 6, 2012 at 7:38pm

I received my Remzibi OSD 3DR today and looking for instructions on how to connect it to my APM2.  I can't seem to find any instructions for the electrical wiring on the Remzibi OSD 3DR, there is a note in the "Store" about the silk screen print error and that is confusing.  "RSSI" is between motor battery and the coms which "+.-" is it refering to?  I have searched the DIY site and can't find anything under Remzibi OSD 3DR.  There is a link for instructions in the Store but it shows a different version of the OSD.

Thanks,  Ed

Comment by Paul Mather on January 17, 2012 at 2:50pm

So far, the 3D Robotics version of the Remzibi OSD does not appear to be compatible with the Remzibi version of the OSD.  I'm awaiting a response from 3DR to explain how I'm supposed to load the firmware, what the buttons do and the status LED's meanings. So at this point, I don't know why it's called Remzibi's OSD.

Comment by Furet on February 17, 2012 at 6:15pm

hello Ed Kirk I have the same problem no assembly instructions
some one find the solution for connect it to APM?

Comment by Chris Kreuzer on February 24, 2012 at 1:43pm

same problem here... How can i connect it to APM 2.0 ?!? 

Comment by Rod on March 9, 2012 at 4:02am

Has anybody managed to get this running?

I cannot get it to respond to the Remzibi OSD Configuration Tool. Whenever I run the serial test I get "Failed: OSD did not respond".


3D Robotics
Comment by Sam Kelly on March 9, 2012 at 10:02am

Rod, have you tried to put the Remzibi in configuration mode by holding down SW1 while resetting or powering up the board? the LED should stay solid and the serial test should report the firmware version.

Comment by Tom Low on March 11, 2012 at 10:17pm

I'm sorry I didn't read these posts more carefully before I spent >$110 w tax and shipping for this seemingly undocumented offering from 3D Robotics.   After spending most of the day trying to figure out the pin assignments and map them onto the real Remzibi (which seems a totally different object) I have given up.  

I hope 3D has plans to document this thing, but given it was released in Dec 2011 and it is now mid March 2012, I wonder.   This is more than a little disappointing.  

Comment by Rod on March 14, 2012 at 4:26am

Thanks Sam,

I got it working. I thought I had tried all combinations of pushing buttons during reset. Now it seems to work fine. 

Tom - I can sympathise with your frustration, but this board does seem to be compatible with the OSD Config tool. Are you able to get the serial test to work correctly? I have managed to successfully download a config, and also hook up GPS, and video in/out. Still waiting on my APM...

Rod.

Comment by Paul Mather on March 14, 2012 at 4:57am

I too am disappointed. I had to buy my own 3DR Remzibi OSD after it came out. Not once was I contacted during development. Once I got mine, I couldn't get it to work with my software. So far, I've been able to get it to program but I can't get it to update firmware.


Moderator
Comment by Sgt Ric on March 14, 2012 at 6:30am
Paul, I am horrified to hear this!
Open source or not, that is not the way you should have been treated!

I had assumed you were part of the 3DR reincarnation, esp after all the hard work you had put in over the years!

Comment

You need to be a member of DIY Drones to add comments!

Join DIY Drones

© 2014   Created by Chris Anderson.

Badges  |  Report an Issue  |  Terms of Service