Veikko Vierola's Discussions (280)

Discussions Started (41) Replies Latest Activity

Pixhawk boot/connection problem after AC 3.2.2 FW install

Hi, Just installed new AC 3.2.2 firmware with APM Planner 2.0. Perhaps something went wrong with the installation cause PH doesn't react no…

Started by Veikko Vierola in PX4 and Pixhawk Hardware

1 Jan 31, 2016
Reply by Veikko Vierola

Pixhawk stays in the ESC calibration mode.

Hi, I have Favourite Sky III 30AX4 4 in 1 ESC. I'm calibrating the ESC like this; 1. I put radio on, I set full throttle 2. I power up Pix…

Started by Veikko Vierola in Miscellaneous

2 Sep 19, 2014
Reply by Veikko Vierola

Pixhawk SBUS support

Hi, I'm using Futaba T8FG Tx and Futaba R6208SB Rx connected to the Pixhawk RC IN port. In the Mission Planner radio calibration page all b…

Started by Veikko Vierola in PX4 and Pixhawk Hardware

1 Sep 2, 2014
Reply by Veikko Vierola

IRIS hover test

Hi, I made IRIS hover test today, here is some specs of the flight: IRIS HOVER TEST WX: OAT    0°C - +1°C Humidity   97% Wind    3m/s Pr…

Started by Veikko Vierola in PX4 and Pixhawk Hardware

3 Jan 2, 2014
Reply by Veikko Vierola

FAIL SAFE reason from logs

Hi, During todays flight Arducopter CODE301RC7 hit FAIL SAFE -> RTL. How can I check afterwards from log what type of FAIL SAFE I had (…

Started by Veikko Vierola in Arducopter 3.x (Multicopter)

1 Dec 7, 2013
Reply by Rob

Autotrim questions

Hi, 1. Is it possible to commence the autotrim procedure without radio switch, can I use some mission planner button to save the autotrim…

Started by Veikko Vierola in Arducopter 3.x (Multicopter)

2 Dec 7, 2013
Reply by Veikko Vierola

Arducopter V3.1-rc7 Quad Firmware installati​on problem @ program phase....

What is wrong?   This is what I do:   I press INITIAL SETUP I press Install Firmware I press Beta firmwares   These are beta firmware, use…

Started by Veikko Vierola in PX4 and Pixhawk Hardware

3 Dec 3, 2013
Reply by Veikko Vierola

3.0.1 rc5 problem? Pixhawk

Hi, I have calibrated radio. In radio calibration: When I push right stick forward the green pitch bar goes up and shows pwm value 1940, st…

Started by Veikko Vierola in Quadcopters

1 Oct 29, 2013
Reply by Veikko Vierola

Only rudder and elevator for steering the plane

Hi, How APM should be configured if you want to use only rudder/elevator (no ailerons) for steering the plane?

Started by Veikko Vierola in ArduPilot Mega hardware: tech support

11 Jun 5, 2013
Reply by Veikko Vierola

Ultra Capacitor for APM power security and VCC stabilizing

Hi, I just tested to put three 5,5V 1.5F ultracapacitors parallel and connected the system to the APM power rail. APM stayed alive 10 secon…

Started by Veikko Vierola in Autopilot hardware

3 Apr 16, 2013
Reply by Veikko Vierola

RSS

© 2019   Created by Chris Anderson.   Powered by

Badges  |  Report an Issue  |  Terms of Service