915MHz Telemetry cuts out... any ideas?

Hi everyone,


I have a Bixler 2 with APM 2.5 and 915MHz telemetry. It flies really well and I've never had any problems with it. However, I've never flown it particularly far away from me. I have tried to do a few surveys on auto mode recently, and the telemetry cuts out at about 300m away from me. I then ran over to the plane in the air (on auto) and it didn't regain signal. Later on it did once it was coming in for landing.

The telemetry logs (attached) show that the noise is always fairly low, and it's the rssi - both air and ground module - that drop sharply, not related to distance.

Any ideas?

Thanks,
Patrick

2014-12-17 13-10-18.rlog

2014-12-17 13-10-18.tlog

2014-12-17 13-10-18.tlog.jpg

You need to be a member of diydrones to add comments!

Join diydrones

Email me when people reply –

Replies

  • Ok, let's try this again. What is the difference between the above picture and these two? The one with the red dot is the 3DR antenna. The other is one I bought last year. I freely admit radio electronics is not my forte'

    s9AyhSq.png

    • And I found the other one, which has a male pin. I was thinking both had to be the same antenna so I didn't use the other one, didn't notice there was one without the male pin. For fun, tonight I used the large antenna in the other picture without the male pin, attached to my phone using Droid Planner.

      I walked to the other end of my house and the signal never dropped below 100%.

      With the 3DR antenna, it wanders all over the place, from 50% to 75-80%.....much like it does in the air. Bottom line: the 3DR antenna is horrible.

      Now I'm wondering if that other antenna could have been used all this time!

      I read this at RCG, but never did the mod:

      See Pattaya01's posts, and jump back to pg 7 & 12 to see the mod.

      http://www.rcgroups.com/forums/showthread.php?t=1963338&page=17

      OGxOvtd.png

      • Huh I just looked at the specifications of that antenna and not at the picture. The specs say SMA plug, but the picture is clearly RP-SMA, which would indeed fit your radio. Sloppy work, jDrones.

        Thanks for bringing my attention to that other thread. A few months ago I lost my radio antenna and wondered if I could use a spare 2.4GHz antenna I had from a Turnigy RC radio because they look exactly the same. I ended up buying another one to play it safe, but now I'm annoyed because now I know it is exactly the same - the wrong one!

        In light of this new information, your new antenna is better because it's a 3dB antenna, but MUCH better because it's actually a 915MHz antenna!

        It looks like you answered your own question, but just in case you missed it - the two antennae you're holding are both RP-SMA connections. I can't see the lengths, but if one is longer, it is probably a 915MHz antenna, while the 3DR one is 2.4GHz. The one you're holding in the bottom picture has an SMA connector

  • 3FIJAv8.png

    It sure looks female to me. My 3dr radio has a male pin. Am I missing something?

    Several months back I ordered two antenna with a male pin. Doh!

  • Moderator

    RSSI is reported signal strength so if they drop sharply it's clear what's happening. Why is another story.

    What antennas are you using? What power are your radio's set at? Are you using ECC?

    • Thanks for the quick response!
      I'm using the stock antennae (which look exactly the same as my 2.4GHz radio and my 5.8GHz FPV antennae...?). How do you set the radio power? What is ECC?

      FPV system is not on the aircraft btw

      • Moderator

        Have a read through here: http://copter.ardupilot.com/wiki/3dradio/

        • Looks like they're set at power level 20 (full) and ECC is turned on...
          I did notice a few weeks ago (before I had the courage to fly far away) that when the aircraft came back with a loose antenna. I know they don't like to transmit without an antenna attached, but if it were damaged it would be completely shot, right?

          • Moderator

            Normally yes, but as they overheat without an antenna that can cause other issues too. The stock antennas are usually not great with range and better ones can make a large difference.

            It doesn't help too that the antennas all look alike and some radios have even been known to ship with the incorrect antennas. It may be worth trying any other antennas you have to see if there's a difference in the RSSI values.

            Also check the antenna connecter to see if it matches the radio, ie SMA or RP-SMA.

            • Ha got it!
              The air module had two females! Interesting that it actually worked for a bit...

              Thanks heaps for your help Graham :)

This reply was deleted.

Activity

DIY Robocars via Twitter
RT @TinkerGen_: "The Tinkergen MARK ($199) is my new favorite starter robocar. It’s got everything — computer vision, deep learning, sensor…
Monday
DIY Robocars via Twitter
Monday
DIY Robocars via Twitter
RT @roboton_io: Join our FREE Sumo Competition 🤖🏆 👉 https://roboton.io/ranking/vsc2020 #sumo #robot #edtech #competition #games4ed https://t.co/WOx…
Nov 16
DIY Drones via Twitter
First impressions of Tinkergen MARK robocar https://ift.tt/36IeZHc
Nov 16
DIY Robocars via Twitter
Our review of the @TinkerGen_ MARK robocar, which is the best on the market right now https://diyrobocars.com/2020/11/15/first-impressions-of-tinkergen-mark-robocar/ https://t.co/ENIlU5SfZ2
Nov 15
DIY Robocars via Twitter
RT @Ingmar_Stapel: I have now explained the OpenBot project in great detail on my blog with 12 articles step by step. I hope you enjoy read…
Nov 15
DIY Robocars via Twitter
RT @DAVGtech: This is a must attend. Click the link, follow link to read the story, sign up. #chaos2020 #digitalconnection #digitalworld ht…
Nov 15
DIY Robocars via Twitter
RT @a1k0n: Got a new chassis for outdoor races (hobbyking Quantum Vandal) but I totally didn't expect that it might cause problems for my g…
Nov 11
DIY Drones via Twitter
First impressions of the Intel OpenBot https://ift.tt/36qkVV4
Nov 10
DIY Robocars via Twitter
Nov 9
DIY Robocars via Twitter
Excellent use of cardboard instead of 3D printing! https://twitter.com/Ingmar_Stapel/status/1324960595318333441
Nov 7
DIY Robocars via Twitter
RT @chr1sa: We've got a record 50 teams competing in this month's @DIYRobocars @donkey_car virtual AI car race. Starting today at 10:00am…
Nov 7
DIY Robocars via Twitter
Nov 6
DIY Robocars via Twitter
RT @a1k0n: Car's view, using a fisheye camera. The ceiling light tracking algorithm gave me some ideas to improve ConeSLAM, and having grou…
Nov 5
DIY Robocars via Twitter
RT @a1k0n: To get ground truth I measured the rug, found the pixel coordinates of its corners, calibrated my phone camera with my standard…
Nov 5
DIY Robocars via Twitter
RT @a1k0n: @DIYRobocars is back in December, but outside. Time to reinvestigate ConeSLAM! I rigged up a quick and dirty ground-truth captur…
Nov 5
More…