Air v1.2: Failed to enter command mode

I recently purchased a set of 915Mhz 3DR Radios from the store and am having trouble verifying the behavior of the 'air' module using a USB-to-TTL device.

The 'ground' module is v1.1 and the mission planner was able to load its settings correctly.

For the 'air' module the mission planner and the radio config tool yield an error message - "Failed to enter command mode", when I attempt to load the settings from the device. The green light stays solid for a second and then flashes steadily as soon as it is plugged in.

Any advice?

-Error Message-

iy9Zp.png?width=450

-Port Settings-

paTGb.png?width=450-Wiring-

yejx3.jpg?width=450

You need to be a member of diydrones to add comments!

Join diydrones

Email me when people reply –

Replies

  • Developer

    Does that USB-TTL use a SiLabs chip?

  • 3D Robotics

    Maybe you've got your RX and TX wires reversed? (RX on one board should go to TX on the other, if memory serves). I'm not familiar with that particular USB-to-serial board. 

This reply was deleted.

Activity

DIY Robocars via Twitter
RT @masato_ka: 距離センサを3つとESP32を付けたラジコンカーをDonkeyCarライクにNNで自動走行。3層FC極小モデルをTensorFlow Lite for microcontrollerで動かしてる。機体は借り物でRumiCarって言います。Tenso…
Monday
DIY Robocars via Twitter
RT @SmallpixelCar: My car was able to go all the way autonomously until the crosswalk. It was only 100 yards from the target. What should b…
Jul 4
Liam left a comment on Agricultural UAVs
"Hi
I'm Liam from T-MOTOR. I would like to reach out to see if there is any possibility for us to work together.
We are a propulsion system manufacturer who offers motors, propellers and ESCs for all kinds of drone applications which vary from secur…"
Jun 30
DIY Robocars via Twitter
RT @SmallpixelCar: Smart move. The car used the shadow to guide it through the bridge. This was never in the training samples. But it learn…
Jun 30
DIY Robocars via Twitter
RT @SmallpixelCar: Getting closer to the target. Single camera. Untrained road. https://t.co/Wsr7RwDamj
Jun 29
Richard Cox left a comment on Australia
"Anyone in the DIYDRONES Australian subgroup based in Alice Springs, NT?
I am experimenting with Ardupilot (standard Arduplane), Pixhawk 4 FC in a 4-ch
RC "AXN Floater Jet" foamy plane..."
Jun 29
Omar Sykes left a comment on Australia
"Hi everyone, I am looking for someone who is good at drone building, repair and software in Adelaide. Please give me a call on 0477 319 219."
Jun 29
DIY Robocars via Twitter
RT @RoboticMasters: #donkeycar https://t.co/czuLoVRcA4
Jun 29
DIY Robocars via Twitter
https://t.co/DKQbNTbz0g
Jun 29
DIY Robocars via Twitter
RT @RoboticMasters: Donkey car, car car car car car car; Donkey car, car car car car car car; Donkey Car. Anyone like our tiny tiny donkey…
Jun 29
DIY Robocars via Twitter
RT @SmallpixelCar: After improving DBSCAN speed, I can get 11 frame per second on @NVIDIAEmbedded Jerson Xavier MAXN mode and the autonomou…
Jun 26
DIY Robocars via Twitter
RT @Heavy02011: Join us at next Virtual Race League: ⁦@diyrobocars⁩ Race #4 - Parking Lot Nerds, August 1st https://t.co/5KUpu7VGaH
Jun 25
DIY Robocars via Twitter
RT @SmallpixelCar: #CUDA implementation should be easy, because most of the time is on distance calculations berween two points and if the…
Jun 25
DIY Robocars via Twitter
RT @SmallpixelCar: This is the view from the car. Even my lanenet inference is fast on @NVIDIAEmbedded Jerson Xavier, DBSCAN clustering tak…
Jun 25
DIY Robocars via Twitter
RT @SmallpixelCar: Ran my car in the park, with single camera and @sparkfun IMU. #TensorRT on @NVIDIAEmbedded Jetson Xavier. Lanenet one fr…
Jun 24
DIY Robocars via Twitter
RT @SmallpixelCar: Making progress on drive the car autonomously in my neighborhood. This run used single camera only. No other sensors. ht…
Jun 24
More…