airspeed sensor not working

ive installed my airspeed indicator but when i tested it in console mode under test the data output i got was nanm/s and it didnt change when i try breathing in the tube

i checked that voltage is presant but im not sure how to check the analoge output has anyone seen this please

cheers

 

forgot to add i changed the firmware to the dec 13 version and it didnt change

You need to be a member of diydrones to add comments!

Join diydrones

Email me when people reply –

Replies

  • Regarding the Analog Airspeed Sensor MPXV7002DP on a Pixhawk and using Qgroundcontrole
    We cannot get this air speed sensor to work on our VTOL Quad (ranger) plane using the Qgc Quadranger firmware. We have it wired into the ADC 6.6v port and when we try to calibrate it the error massage comes up. Its on and working and Qgc seems to detects it but always comes up with and error, [cal] calibration failed: airspeed. Any ideas?

  • Hi All,

    I have a problem with my airspeed indicator ( MPXV7002DP ) When ever i check the voltage on the pins its shows 

    Pin 2 & 3 = 4.9v

    Pin 2 & 4 = 4.8v  

    Pin 3 & 4 = .01v

    Any body has same problem ? 

    Thanks

    Aytek

  • @chris I couldn't find the manual many thanks for that massive help.
  • Hi I have the API model number MPXV7002DP. I can not see anywhere which way u put the silcon pipes on and no where how and where it goes on the APM 2.5 board. Could someone please help and im so fed up trying different things and worrying if im about to destroy the board!!!!

  • FYI, I had something happen today on this subject; It was rather amusing in the end; so I just had to share...

    I happend to be switching back and forth between ACM and APM codes today, just messing around with HK's GCS; and such. But at some point I noticed the airspeed sensor had stopped responding in the APM CLI test. Not really paying any attention, I couldnt say exactly when it had stopped working. It had me stumped for a bit, checking cables, voltages; and even to the point of removing it and putting it on another APM/OP I have... Long story short, but to resolve it (insert drum roll here) all I simply had to do was 1) RELAX; and 2) do a reset in setup mode; and all is better...

    Ya I know, I know; just fall back to basics...

    Did you plug it in (lol)

    Darren

    (PS I have a 5004 as well)

  • Distributor

    Which air speed sensor are you using?  This one or This one

     

    If you are using the MPXV7002DP then check the following on your air speed sensor.

     

    No air pressure in pipes:


    Pin 2 & 3 = 4.9v
    Pin 2 & 4 = 2.46v
    Pin 3 & 4 = 2.42v

    Air pressure in bottom tube:


    Pin 2 & 4 = 4.8v
    Pin 3 & 4 = .03v


    Air pressure in top tube:


    Pin 2 & 4 = .03v
    Pin 3 & 4 = 4.86v


    I have shown the pin numbers on the file attached, the voltage did not change on pins 2 & 3 throughout the tests.

     

     

    3692145102?profile=original

    Please post back with the additional informtion.

     

    Kind Regards

     

    Martin.


    www.buildyourowndrone.co.uk

     

     

     

This reply was deleted.

Activity

DIY Drones via Twitter
RT @Struktur3D: We have just posted on @DIYDrones for the first time in a long time. Continuing with our search for a #lasercutting service…
19 hours ago
DIY Robocars via Twitter
RT @chr1sa: The dev team is having fun with virtual @DIYRobocars track generation with Unity on the @donkey_car discord: https://t.co/l0Jd9…
Wednesday
DIY Drones via Twitter
Review of the new Nivida Jetson NX for robocars https://t.co/bWjd3sH2o4
Tuesday
DIY Robocars via Twitter
RT @chr1sa: My review of the new @NVIDIAEmbedded Jetson Xavier NX in robotics and @DIYRobocars applications https://t.co/O7TfJZhiF9 https:/…
Monday
DIY Drones via Twitter
RT @chr1sa: Somehow I missed this, but last week @Nvidia released a new version of its Isaac robot development framework. Lots of new Lidar…
Monday
DIY Robocars via Twitter
RT @Smartphone89: DonkeyCar Racing League Korea #donkeycar @diyrobocars https://t.co/mDlHDR1d98
May 29
Jørn Ramnæs liked VIDEO LINK's profile
May 28
Mark Harrison left a comment on Moderators
"Wow, Ning2 looks really great on mobile. I had sort of drifted away as my browse-time went more on my phone, so this is great."
May 28
DIY Robocars via Twitter
https://t.co/rLmFr8M2UK
May 28
DIY Drones via Twitter
Welcome to the new DIY Drones design!. You may have noticed that DIY Drones looks a little different today. That's… https://t.co/cg2EmeDGMQ
May 27
DIY Drones via Twitter
New! Online Training on Drones for Disaster Response https://t.co/brqRuujjY2
May 26
DIY Robocars via Twitter
https://t.co/8EMCvYW6oz
May 25
DIY Robocars via Twitter
RT @OttawaAVGroup: We are going to try something new this week. We will be having a drop-in style meeting Wednesday @ 7-9pm EST. Pop in and…
May 25
DIY Robocars via Twitter
RT @tawnkramer: Thanks Everyone for another fun virtual race! Amazing Ai racers competing head-to-head, Virtual Makers Fair event. Catch us…
May 23
DIY Robocars via Twitter
RT @make: Find out the latest from @diyrobocars at 10am PT from @chr1sa of @3DRobotics on Virtually Make Faire! #makerfaire #maketogether #…
May 23
DIY Robocars via Twitter
RT @Heavy02011: Join us Saturday online: Virtual Race League: @DIYRobocars Race #2 - Parking Lot Nerds https://t.co/aJUu4sdutx #Meetup via…
May 22
More…