Good day guys !!  

I feel the need to obtain the information from my PixHawk in my Graupner MZ-24 screen. I found
some threads talking about a change in arducopter firmware to run the telemetry, not good at messing original controller firmware.

Then I found an "adapter" that staff of the AutoQuad made to convert the MavLink in Hott telemetry.

I come here to share a few changes I made in the project Mav2Rott downloaded here: http://autoquad.org/software-downloads/?did=31.
This is an adaptation to send the telemetry PixHawk for Graupner Hott Protocol.

Is correct with some features:

Battery Voltage;
Altitude for barometer;
Satellite count Speed;
Flight Modes Current drawn by the motor;
Direction of the Head;

I am not able to make it work:

Correct display Latitude and Longitude;
Distance of Home;
Direction of Home;

If anyone can help thank you very much.
The project is attached to the topic. The connections are equal to the jd-ioboard. I am using an Arduino Pro Mini.

Mav2HoTT_NoLeds.zip

You need to be a member of diydrones to add comments!

Join diydrones

Email me when people reply –

Replies

  • Hi is there anyone who is using vario voice from graupner mx20. It doesn't work corectly in my setup any idea why ?
  • Ok so I found how to disable "minimum altitude" in "fence alerts" min altitude must be set to OFF

  • Hi and another question. After take off I still hear "minimum altitude" message on my earphones from mx20. Does anyone knows how to disable that alert ?

  • Is that normal that from time to time telemetry is 0000 and after one second it's showing data again ?



  • Michel Kosloff said:


    What model of receiver do you have?

    I use GR-16.



  • Ultrafuge said:

    Hi,

    With the original schematic (Power from Pixhawk to 'Vcc' I get fluctuating Rx voltage display.
    I get much better results by powering the Arduino from the Rx (Rx on 2s). Red wire goes to 'RAW' and NOT to 'Vcc' !!! Signal (white / orange) goes to '3' and black/brown to 'GND'.
    Two wires ('RXI' and 'GND') to Pixhawk.

    What model of receiver do you have?

    I experienced similar behavior only with GR-12/GR-12L

  • New version is available here http://mediamax.pro/MAVLink2HoTT/

    MAVLink2HoTT
  • Hi,

    With the original schematic (Power from Pixhawk to 'Vcc' I get fluctuating Rx voltage display.
    I get much better results by powering the Arduino from the Rx (Rx on 2s). Red wire goes to 'RAW' and NOT to 'Vcc' !!! Signal (white / orange) goes to '3' and black/brown to 'GND'.
    Two wires ('RXI' and 'GND') to Pixhawk.

  • Hi Kay

    I had the interface running with an APM mini from Hobbyking. The MavLink2Hott interface was connected parallel to minimOSD. In the meantime I changed APM mini to Pixracer from Hobbyking and it is working as before.

    Please check settings from @FLO and check settings according to MAVLink2Hott where I started the same project, but didnot finish, because this interface works perfect.

    You have to define data sent out on the serial interface you are using. E.g. if you use Serial 3 on Pixhawk, you have to define all SR3 parameters as described before. 

    best regards

    Hannes

    j-lang/MAVLink2Hott
    Interface for Ardupilot (Pixhawk, APM ...) to Graupner HoTT receiver to deliver Ardupilot telemetry data to Graupner transmitter. - j-lang/MAVLink2Ho…
  • Hello Kay,

    I think SR1 and SR2 are the telemetry ports 1 and 2 on the pixhawk. But as you have an APM, I'm not sure...

    Flo

This reply was deleted.

Activity

DIY Robocars via Twitter
Sep 9
DIY Robocars via Twitter
RT @chr1sa: We've got another virtual @DIYRobocars race tomorrow at 9:00am PT. Two dozen autonomous cars will compete, four at a time. Ther…
Sep 4
DIY Robocars via Twitter
Sep 1
DIY Robocars via Twitter
Aug 31
DIY Robocars via Twitter
Aug 31
sam liked Jimmy Oliver's profile
Aug 25
DIY Robocars via Twitter
RT @ExplorerRobocar: Sometimes, I am really a big kid!! Having fun with my virtual RC car on the @diyrobocars track 😜😉, by using the « AR R…
Aug 24
DIY Robocars via Twitter
RT @grepLeigh: @donkey_car @unity3d @TensorFlow ~1050 episodes into training, my agent learned to erratically drive in the left lane. 🤖😆 ht…
Aug 24
DIY Robocars via Twitter
RT @EclipseCyclone: Sweet! http://Robotec.ai high performance #ROS 2 @unity3d #CycloneDDS bridge for @AutowareFdn @SVLSimulator now…
Aug 24
DIY Robocars via Twitter
RT @a1k0n: My car had a lot of trouble getting around the track at the last @diyrobocars event -- only one actual finished lap during the r…
Aug 24
DIY Robocars via Twitter
RT @SmallpixelCar: This is the run time map https://t.co/VzykOkUt2G
Aug 24
DIY Robocars via Twitter
RT @SmallpixelCar: Made a lot progress on Warm Spring Raceways track. Almost finished one lap. https://t.co/nUVpufZQyP
Aug 24
DIY Robocars via Twitter
RT @AntonioRobotics: Super fun time seeing these autonomous cars race at @circuitlaunch for the @diyrobocars quarterly meet up! The demolit…
Aug 15
DIY Robocars via Twitter
RT @a1k0n: I thought my dumb localization code was still working at the new @circuitlaunch track, but it was just *barely* working. I shoul…
Aug 14
DIY Robocars via Twitter
RT @DAVGtech: Recording of entire in person @diyrobocars race today @circuitlaunch. Fast forward a couple hours to go straight to the racin…
Aug 14
DIY Robocars via Twitter
RT @SmallpixelCar: This is the run time map. Very noisy Lidar signal https://t.co/bAbeVUMi10
Aug 14
More…