Composite Scratch Built with Rascal 110 wing

I am a couple weeks into a new project I started.  The goal is make a long endurance (2+ hours) aircraft capable of carrying a couple pounds of payload using an off the shelf wing.

  • I chose the Rascal 110 wing for its lifting capacity (I think the typical weight is 12lbs) and its efficiency.  The Rascal 110 can almost be flown as a glider and I have seen it ride thermals very well. With about 1550 sq.in. of area it will have a light wing loading.
  • The fuselage will be a 4.5" carbon fiber tube about 55" long.  This was made in 2 pieces using braided CF sleeve and a single layer of cloth wrapped around a PVC pipe.  Special heat shrink tubing was used in place of vacuum bagging.  
  • For propulsion it will have a DLE-20 setup in a pusher configuration.  The DLE-20 will be a little overkill in terms of power but it should be easy to prop for endurance which will take away from total power output slightly.  It will sit on a anit-vibration mount to help smooth things out.
  • The gas tank will be built into the fuselage under the wing and centered on the estimated CG.  The epoxy is still wet but once it dries I'll know the exact capacity... should be in the 40-50oz range :).  There will be a sump hanging from the bottom feeding a header tank to ensure reliable fuel delivery.  The tank will be packed with fuel tank foam to prevent sloshing.
  • Since it is a pusher, tail configurations are limit.  I could of gone twin boom but that would be annoying with the 2 piece wing.  If I was using a 3 piece wing I would definitely go that route.  Instead this airplane will have full flying canards up front and a vertical stab in between the engine and wing.  
  • The forward fuselage will be completely empty  except for the nose gear mount/servo and the canard servo; leaving plenty of room for payload.  
  • The nose will likely be tipped with a camera to feed into an OSD and video Tx.  Also installed will be a PixHawk once my preorder arrives. 

 

I will update this thread as things slowly progress.

You need to be a member of diydrones to add comments!

Join diydrones

Email me when people reply –

Replies

  • Looking forward to seeing the finished item. look's good so far.

  • Looking pretty cool brother, I would love to see the whole thing and see what your wings look like on it too.

  • Nice work! Keep it up!
  • Gas tank

    3692848521?profile=original

    Fuel sump to be glued on the bottom of the tank/fuselage

    3692848456?profile=original

  • Made a CF sheet for various pieces in the sing saddle and fuel tank

    3692848002?profile=originalWing Saddle Lay Up

    3692847634?profile=original

    3692848027?profile=original

    Wing Saddle cleaned up

    3692847963?profile=original

    3692848059?profile=original

    Mounting Saddle to the Fuselage 

    3692848104?profile=original

    3692848119?profile=original

    Molded center panel.

    3692848084?profile=original

    3692848159?profile=original

    Glued to fuselage

    3692848144?profile=original

    3692847978?profile=original

  • PVC Pipe for molding3692848407?profile=original

    Braided Carbon Fiber

    3692848366?profile=originalFuselage half

    3692848392?profile=original

This reply was deleted.

Activity

DIY Drones via Twitter
RT @chr1sa: My talk on PX4 and FAA certification is coming up at 1:45 PST today on the PX4 Dev Summit livestream. Includes some cool new st…
yesterday
DIY Drones via Twitter
RT @seesharp: I'm tuned into the PX4 / Dronecode free live conference. Great stuff. Microsoft AirSim talk in 10 minutes. https://t.co/0zbZ2…
Monday
DIY Robocars via Twitter
RT @masato_ka: 距離センサを3つとESP32を付けたラジコンカーをDonkeyCarライクにNNで自動走行。3層FC極小モデルをTensorFlow Lite for microcontrollerで動かしてる。機体は借り物でRumiCarって言います。Tenso…
Monday
DIY Robocars via Twitter
RT @SmallpixelCar: My car was able to go all the way autonomously until the crosswalk. It was only 100 yards from the target. What should b…
Saturday
Liam left a comment on Agricultural UAVs
"Hi
I'm Liam from T-MOTOR. I would like to reach out to see if there is any possibility for us to work together.
We are a propulsion system manufacturer who offers motors, propellers and ESCs for all kinds of drone applications which vary from secur…"
Jun 30
DIY Robocars via Twitter
RT @SmallpixelCar: Smart move. The car used the shadow to guide it through the bridge. This was never in the training samples. But it learn…
Jun 30
DIY Robocars via Twitter
RT @SmallpixelCar: Getting closer to the target. Single camera. Untrained road. https://t.co/Wsr7RwDamj
Jun 29
Richard Cox left a comment on Australia
"Anyone in the DIYDRONES Australian subgroup based in Alice Springs, NT?
I am experimenting with Ardupilot (standard Arduplane), Pixhawk 4 FC in a 4-ch
RC "AXN Floater Jet" foamy plane..."
Jun 29
Omar Sykes left a comment on Australia
"Hi everyone, I am looking for someone who is good at drone building, repair and software in Adelaide. Please give me a call on 0477 319 219."
Jun 29
DIY Robocars via Twitter
RT @RoboticMasters: #donkeycar https://t.co/czuLoVRcA4
Jun 29
DIY Robocars via Twitter
https://t.co/DKQbNTbz0g
Jun 29
DIY Robocars via Twitter
RT @RoboticMasters: Donkey car, car car car car car car; Donkey car, car car car car car car; Donkey Car. Anyone like our tiny tiny donkey…
Jun 29
DIY Robocars via Twitter
RT @SmallpixelCar: After improving DBSCAN speed, I can get 11 frame per second on @NVIDIAEmbedded Jerson Xavier MAXN mode and the autonomou…
Jun 26
DIY Robocars via Twitter
RT @Heavy02011: Join us at next Virtual Race League: ⁦@diyrobocars⁩ Race #4 - Parking Lot Nerds, August 1st https://t.co/5KUpu7VGaH
Jun 25
DIY Robocars via Twitter
RT @SmallpixelCar: #CUDA implementation should be easy, because most of the time is on distance calculations berween two points and if the…
Jun 25
DIY Robocars via Twitter
RT @SmallpixelCar: This is the view from the car. Even my lanenet inference is fast on @NVIDIAEmbedded Jerson Xavier, DBSCAN clustering tak…
Jun 25
More…