Hi all.

I'm trying to connect a couple of LED strips to my quad multirotor (3DRobotics). The LED strips can take up to 12V input.

I have purchased the Turnigy Receiver Controlled Switch, and have a bit of a struggle finding out how to connect it to my APM 2.5 and my Graupner GR-24 HoTT receiver.

The specifics for the R/C Switch says max. 5V input. I have read the wiring diagram that comes with the R/C switch, but that didn't help too much. Is it so that I should connect the 3-wire connector to my receiver to provide it also with 5V power?

In that case, which socket/channel should I use on my receiver? I have the GR-24 connected to my APM thru PPM, using socket/channel 8 on the receiver.

And how do I set the appropriate control on my Graupner MX-20 transmitter? I want to use my 2 position switch SW2. How do I get this switch to control the R/C switch?

Is it as easy as I think: Connect the R/C switch to socket/channel 1 on my receiver, and then assign the SW2 to channel 1?

As you probably guessed already, I'm a total newbie to this R/C hobby. I would rather ask a couple of questions (as simple as they may seem), than blowing up my APM or destroying my Lipo-battery or something else.

Views: 4594

Reply to This

Replies to This Discussion

The three-wire connector plugs into an empty channel on your receiver. That provides control and power for the switch itself and that's what the 5V reference is about. The single bigger red wire is what's switched. It can handle up to 10 amps and 30 volts. One end will go to the + side of your battery, the other to the + side of the LED strips. You'll assign a switch on your transmitter to the receiver channel, it looks like yo9u have that figured out. 

It is recommended good practice to keep all of this, and similar auxiliary devices, powered separately from the APM (even if the load is theoretically acceptable). That way if anything goes wrong it is much less likely to take the APM down. Some of us go further than that. I don't like to power anything other than the critical systems (motors, Rx, APM)  from the main batteries, but rather from a small separate battery. That's how I'm powering my LED strips and my camera gimbal, That way if there's a short it doesn't compromise the main battery. 

Also, do you really feel the need to be able to switch the LED strips on and off in flight? I simply plug mine in and leave them on. Even if you're using the main battery you won't notice the difference in flight time. That way you don't need a switch at all, just a power tap to plug into. I use JST connectors, they are tiny and light,

Hope that helps.

 

Thanx for the reply. Good points you made.

About plugging the switch into my receiver: Doesn't matter which channel I use, as long as I assign the chosen one with my TX?

About a second battery, what do you suggest - a 2S Lipo? What size? Do you have a recommendation?

What secondary battery do you use? I'm also considering mounting a camera gimbal. So I can get a 2S Lipo to support both these things?

Right, any empty channel will do. Mind the polarity when you plug in the wires.

The LEDs will be brighter on higher voltage, so use a 3S. Smallest one you can find, Hobby King has a 180 ma that weighs one ounce.

To also power the Gimbal I use a 3s 350 ma, weighs 2 oz. For the gimbal or other such devices you'll also need a BEC to drop and regulate the voltage, you can use a real small one, like a 5 amp.

Remember that with the exception of the LEDs various devices can't just be hooked straight up to batteries but require a BEC. I should have mentioned that earlier. So to maintain independence of the aux. systems and the main system you have one BEC running the flight electronics and another running the gimbal etc.  Now, most motor ESCs have a built-in BEC, so perhaps you are running your flight electronics off of one of those. Or, it can be a stand-alone.

Just about all BECs can be run on 2S or 3S, most on more. 3S gives you a cushion and is generally more efficient than 2S.  The "C" rating (rapid discharge capability) doesn't matter in this sort of application, and lower C is cheaper.

IOBoard

Easiest and safest way to do it would be with IOBoard. It has 6 high voltage outputs, can read rc input and many other things.it is full Arduino mini compatible can you can easily program it to do different type light patterns. There is small sample programto make it working with APM too as IOBoard is MAVlink aware.

Jani,

MegaFlare has a couple questions about his IOBoard here:

http://www.diydrones.com/profiles/comment/list?attachedToType=User&...

Can you point him in the right direction?

-Mike

Voila.

Finished with the connection. For now, I just connected the load for LED strips together with the main power supply. I will get a small secondary Lipo for my additional stuff in a bit, such as LED, camera gimbal, video transmitter etc.

Worked like a charm connecting it the way I suggested (and approved by Oliver).

Thanks for all the help to all of you.

Reply to Discussion

RSS

© 2019   Created by Chris Anderson.   Powered by

Badges  |  Report an Issue  |  Terms of Service